What ASTM A519 Grade 1012 Tubing Is
ASTM A519 is the standard specification covering seamless and cold drawn welded carbon and alloy steel mechanical tubing made for mechanical, structural and pressure service rather than for line pipe duty. Grade 1012 sits at the low-carbon, unalloyed end of the grade range included in the specification. With a nominal carbon range of 0.10–0.15% and manganese of 0.30–0.60%, it corresponds closely to the 10# carbon steel produced by Chinese mills, which is why 1012 tubing is widely chosen for general engineering work where moderate strength, good formability and reliable weldability matter more than high load capacity.
In the annealed or normalized condition the material is soft and ductile, so it is normally supplied either hot finished or cold drawn. Cold drawing improves dimensional accuracy and surface finish while work hardening the wall, so a single grade can be delivered across a range of strength levels simply by changing the amount of cold reduction and the finishing pass.
Chemical Composition and Mechanical Requirements
| Element | ASTM A519 grade 1012 |
| Carbon | 0.10–0.15% |
| Manganese | 0.30–0.60% |
| Phosphorus | 0.040% max |
| Sulphur | 0.050% max |
ASTM A519 does not publish one single set of mechanical values for a grade. Minimum tensile strength, minimum yield strength and minimum elongation are tabulated separately for each grade and for each delivery condition, so a 1012 tube supplied hot finished, cold drawn, or cold drawn and stress relieved carries different minimum properties. The correct way to specify the material is to quote the grade together with the delivery condition and, where the duty is severe, to agree a tensile test on the finished tube.
Sizes, Tolerances and Delivery Conditions
Grade 1012 mechanical tubing is commonly produced with outside diameters from about 3.2 mm up to 304.8 mm, with wall thicknesses from light schedules through to heavy walls, and intermediate sizes can be supplied when tooling is available. Wall tolerance, straightness, ovality and length tolerances follow the tables of ASTM A519, and cold drawn tubing is normally ordered to tighter tolerances than hot finished tubing. Hydrostatic or eddy current examination can be specified where the tube has a pressure-containing function.
Typical Applications
Hydraulic and pneumatic cylinder barrels, piston rods and sleeves
Shafting, bushings and bearing housings in general machinery
Automotive and motorcycle components such as spacers, tubes and brackets
Fittings, couplings and low-pressure fluid transfer lines
Frames, display structures and general fabricated assemblies
Fabrication and Corrosion Protection
The low carbon content gives 1012 excellent bendability, flaring and swaging behaviour and makes it straightforward to weld by conventional arc, TIG and resistance processes. Preheat is generally unnecessary for thin and medium walls, although heavy sections benefit from a modest preheat to avoid rapid cooling. Because the steel is unalloyed it has no inherent atmospheric corrosion resistance, so external protection is normally applied: hot dip galvanizing for outdoor structures, phosphating or black oxide for short-term protection and improved appearance, and epoxy-type coatings for chemical or marine environments.
FAQ
Q: What is ASTM A519 grade 1012 tubing used for?
It is used for mechanical components rather than for fluid transmission lines: cylinder barrels, shafting, bushings, spacer tubes, couplings and general fabricated parts where moderate strength and good formability are sufficient.
Q: Is grade 1012 the same as AISI 1012?
The 1012 designation describes the steel chemistry. ASTM A519 is the product specification that adds the requirements for dimensions, tolerances, mechanical properties and testing of the finished tube, so A519 1012 identifies both the grade and the tubular product form.
Q: Which delivery conditions are available for 1012 tubing?
The usual conditions are hot finished, cold drawn, and cold drawn then stress relieved or annealed. Each condition carries its own minimum mechanical properties in the ASTM A519 tables, so the condition must always be stated on the order.
Q: Can 1012 tubing be welded?
Yes. The low carbon and low manganese content gives good weldability with arc, TIG and resistance welding. For heavier walls a preheat of roughly 100–150 °C is often applied to limit cooling rate, and welds should be made with clean, dry consumables.
Q: How should 1012 tubing be protected against corrosion?
Because it is a plain carbon steel, protection depends on the environment. Hot dip galvanizing suits outdoor structures, phosphating or blackening suits indoor parts needing short-term protection, and organic coatings are used for chemical or marine exposure.
Q: What sizes can be supplied in grade 1012?
Outside diameters from approximately 3.2 mm to 304.8 mm are routinely produced, with walls from light schedules to heavy walls. Non-standard intermediate sizes can be quoted against available tooling and minimum order quantity.





