Aug 29, 2025 Leave a message

S30489 Steel Pipe: Nitrogen-Bearing Austenitic Stainless Tube

Material Definition and Standards

S30489 covers the nitrogen-bearing, nickel-lean austenitic stainless steel designated 06Cr19Ni10N in Chinese practice. It is an 18-8 chromium-nickel austenitic with deliberate nitrogen additions and carbon held at or below 0.08 percent. Nitrogen strengthens the lattice by solid solution, so the grade reaches a higher strength level than a plain 304 type while staying fully austenitic at room temperature.

Seamless tube is normally supplied to GB/T 14976 for fluid transport and welded tube to GB/T 12771. Where an American specification is preferred, the equivalent nitrogen-bearing austenitic composition can be ordered under ASTM A312 as a TP304N type material and tested to the mechanical and corrosion requirements of that specification.

Chemical Composition

Element Range or maximum
Carbon, C 0.08 max
Silicon, Si 1.00 max
Manganese, Mn 2.00 max
Phosphorus, P 0.045 max
Sulfur, S 0.030 max
Chromium, Cr 18.00 to 20.00
Nickel, Ni 8.00 to 10.00
Nitrogen, N 0.10 to 0.25

Nitrogen carries the strength of the grade, so it is the value that must be verified on the heat analysis. Two heats inside the same chromium and nickel bands can differ by a full strength class if their nitrogen contents differ.

Mechanical and Corrosion Performance

The grade is supplied with a minimum tensile strength normally specified at 650 MPa or above, with yield strength and elongation agreed according to the delivery condition, whether annealed or cold finished. Cold drawing raises strength and hardness further and reduces ductility, so the final temper and the required elongation are stated on the order. Corrosion behaviour follows the 304 family: the pitting resistance equivalent number is about 19, and the material passes the intergranular corrosion test of GB/T 4334 when carbon is controlled as shown above. The grade is not a substitute for molybdenum-bearing grades in chloride-rich media.

Typical Applications

Curtain wall support frames and exposed structural members on high-rise buildings.

Salt-spray resistant fasteners and fittings on coastal and cross-sea structures.

Food processing and transport lines requiring a clean, corrosion resistant bore.

Purified water and process lines in pharmaceutical and beverage plants.

Cold drawn precision tube for instrumentation and hydraulic assemblies.

Selection, Welding and Processing Notes

Against a standard 304 type the grade gives a higher strength level and a stronger response to cold work, so thinner walls can often carry the same duty. Against a molybdenum-bearing 316L type it is stronger and lower in cost but less resistant to chloride pitting, which makes it unsuitable for marine immersion or high-chloride process streams.

Limit heat input during welding; excessive heat raises nitrogen porosity risk and widens the heat affected zone.

Use a matching nitrogen-bearing filler or an austenitic filler agreed for the joint, and control interpass temperature.

Keep delta ferrite in the weld metal within the band agreed for the application to limit solidification cracking.

Remove iron contamination from tools and work surfaces; carbon steel brushes leave free iron that rusts in service.

Clean and passivate after forming and welding so the chromium oxide layer re-forms evenly.

FAQ

Q: What is S30489 steel pipe?
Tube made from the nitrogen-bearing, nickel-lean austenitic stainless steel known as 06Cr19Ni10N in Chinese practice, with chromium at 18 to 20 percent, nickel at 8 to 10 percent and nitrogen at 0.10 to 0.25 percent.

Q: How does S30489 differ from ordinary 304?
The difference is nitrogen. It replaces part of the nickel and raises the strength level, so a given pressure duty can be met with a thinner wall while corrosion behaviour stays close to the 304 family.

Q: Which standards apply?
Seamless tube is normally supplied to GB/T 14976 and welded tube to GB/T 12771, with the equivalent nitrogen-bearing austenitic composition available under ASTM A312 where an American specification is required.

Q: Why is nitrogen content tested so carefully?
Nitrogen produces the strength of the grade. A heat at the low end of the band and one at the high end both pass the composition limits but do not deliver the same tensile result.

Q: Is S30489 suitable for seawater service?
Not for continuous immersion. Without molybdenum the grade is prone to chloride pitting, so a molybdenum-bearing austenitic or a duplex grade is the better choice there.

Send Inquiry