EN 10217-2 P195GH Steel Welded Pipe
video

EN 10217-2 P195GH Steel Welded Pipe

EN 10217-2 P195GH (BS EN 10217-2 P195GH) is an HFW welded round steel pipe with a minimum yield strength of 195 MPa at a wall thickness of ≤16 mm and 320 – 440 MPa tensile strength for pressure purposes with high-temperature properties. In addition, it is divided into TC1 and TC2...
Send Inquiry
Chat Now
Product Introduction

EN 10217-2 P195GH (BS EN 10217-2 P195GH) is an HFW welded round steel pipe with a minimum yield strength of 195 MPa at a wall thickness of ≤16 mm and 320 – 440 MPa tensile strength for pressure purposes with high-temperature properties. In addition, it is divided into TC1 and TC2 depending on the test category that can be selected.

The steel number is 1.0348.

Note: BS EN 10217-2 P195GH is fully equivalent to EN 10217-2 P195GH, except for the application region. All of the following requirements apply to BS EN 10217-2 P195GH.

Chemical Components

Chemical composition EN 10217-2 P195GH
C 0.13 % max
Si 0.35 % max
Mn 0.70 % max
P 0.025 % max
S 0.020 % max
Cr 0.30 % max
Mo 0.08 % max
Ni 0.30 % max
Al tot 0.020 % min
Cu 0.30 % max
Nb 0.01 % max
Ti 0.03 % max
V 0.02 % max
Cr+Cu+Mo+Ni 0.70 % max

For Al/N ratios ≥ 2, if nitrogen is fixed by niobium, titanium, or vanadium, details of which shall be reported, this requirement does not apply except that when using titanium, the steel producer shall verify that (Al+Ti/2) ≥ 0.020 %;

Mechanical Properties

Steel grade Tensile properties at room temperature Impact properties
Upper yield strength or proof strength
ReH or Rp0.2
Tensile strength
Rm
Elongation
A
Minimum average absorbed energy
KV2
at a temperature
l t
l t 0 ℃ -10 ℃ 0 ℃
P195GH 195 MPa min 320 – 440 MPa 27% min 25% min 40 J 28 J 27 J

l = longitudinal, t= transverse;

As the temperature increases, the strength of EN 10217-2 decreases, and it is important to understand this change for the safety of piping that is often used in high-temperature and high-pressure environments. The change in P195GH is shown below:

Steel grade Proof strength Rp0.2
MPa, min
at a temperature of ℃
100 150 200 250 300 350 400
P195GH 175 165 150 130 113 102 94

Manufacture Process

en 10217-2 P195GH is manufactured using the process of HFW (high-frequency welding). EN 10217-2 requires that it be manufactured using a current of 100 kHz or greater.

The weld area shall be free from cracks and lack of fusion. Repairs to the weld seam of HFW tubes are not permitted.

ERW Steel Pipe Manufacture Process

Depending on the raw material, molding, and delivery conditions, there are several manufacturing routes, which are not specified in EN 10217-2.

Route N° (according to Part 1) Manufacturing routes Acceptable delivery condition a
Starting material Forming operation
1c As (hot) rolled strip Cold formed and welded NP
1d NR
2b Normalized rolled strip NW
2c NP
2d NR

a: NP = tube full body normalized; NW = normalized weld zone; NR = normalized rolled or hot (stretch) reduced within the normalizing temperature range.

Dimension

EN 10217-2 195GH steel pipe dimensions generally include the following ranges:

Outer diameter: 10.2 mm – 610 mm;

Wall thickness: 1.4 mm – 16 mm;

And there are three series of preferred thicknesses provided in the standard.

Series 1 = diameter for which all the accessories needed for the construction of the piping system are standardized;

Series 2 = diameter for which not all the accessories are standardized;

Series 3 = diameter for special applications for which very few standardized accessories exist;

If you want to know the dimensional tolerances or the requirements for sealing of steel tubes you can click on the EN 10217-2 specification to view it.

Appearance Requirement

The internal and external surface finish of the steel pipe shall be typical of the manufacturing process, and heat treatment shall be employed.

Normally the finish and surface condition shall be such that any surface imperfections requiring dressing can be identified.

Any surface imperfection, that is demonstrated to be deeper than 5 % of the wall thickness Tor3 mm, whichever is the smaller, shall be dressed.

EN 10217-2 P195GH Equivalent

BS DIN ISO ASTM
BS EN 10217-2 P195GH DIN EN 10217-2 P195GH ISO 9330-2 PH23 -

We Supply

Products: EN 10217-2 P195 HFW welded steel tubes;

Dimensions: 10.2 mm – 610 mm;

Wall thickness: 1.4 mm – 16 mm or on request;

Length: 6 m, 12 m or customized;

Ends: Flat ends, beveled ends, composite ends;

Coating: Paint, galvanized, epoxy resin, 3LPE, 3LPP, etc;

Packaging: Bundle, pipe end protector, sling, tarpaulin;

Support: FOB, CIF, OEM and so on;

 

Hot Tags: en 10217-2 p195gh steel welded pipe, China en 10217-2 p195gh steel welded pipe manufacturers, suppliers, Seamless Mechanical Tubing, LSAW Pipes, Stainless Steel Efw Pipes, Black With Blue Strip Pipe, Pipe Roll 8 Inch, HDPE Plastic Water Supply Pipe

Send Inquiry