The Grade
API 5L X46 is the line-pipe grade with a specified minimum yield strength of 46,000 psi (317 MPa) and a specified minimum tensile strength of 63,000 psi (435 MPa). It sits between the general X42 grade and the higher X52, and it is specified when the design needs a modest strength increase without paying for the full step to X52. The grade is available at both PSL1 and PSL2 levels, and as a spiral submerged arc welded (SSAW) product it is made from hot-rolled coil in large diameters at the lowest manufacturing cost.
Manufacturing
In the SSAW process, hot-rolled coil is levelled, edge-prepared, and fed into a forming line at a controlled helix angle, so that the strip edges meet along a continuous spiral. The seam is welded by double-sided submerged arc welding, giving full penetration under a blanket of granular flux, and the pipe is then sized, cut to length, and end-prepared. SSAW is the most economical process for diameters from about 508 mm to 2032 mm, and it allows very long individual lengths that reduce field girth welds.
Chemistry
The typical maximum limits for X46 at PSL1 are approximately 0.26 to 0.28% carbon, up to 1.40% manganese, 0.030% phosphorus, and 0.030% sulphur, with the exact values taken from the current edition of API 5L. The steel is a carbon-manganese composition with micro-alloying as needed, and the carbon equivalent is kept moderate so that the pipe welds reliably. PSL2 tightens the chemistry, limits the carbon equivalent, and adds mandatory Charpy impact testing of the body, weld, and heat-affected zone.
Mechanical Properties
The guaranteed properties are a minimum yield strength of 46,000 psi (317 MPa) and a minimum tensile strength of 63,000 psi (435 MPa), with the elongation calculated from the API 5L formula for the test piece. At PSL1 the yield-to-tensile ratio is not limited; at PSL2 it is capped at 0.93, and impact testing is mandatory for the specified sizes. Each pipe is hydrostatically tested, and the spiral weld is examined 100% by ultrasonic or radiographic methods.
Sizes and Lengths
SSAW X46 pipe is commonly produced from about 508 mm (20 inches) to 2032 mm (80 inches) outside diameter, with wall thicknesses from about 6 mm to 20 mm and lengths of 6, 12, or 18 metres. The dimensional tolerances follow API 5L, and tighter controls can be agreed by reference to ISO 3183 or the project specification.
Applications
X46 SSAW is used for onshore oil and gas gathering and transmission lines at moderate pressure, large-diameter water mains and irrigation systems, slurry and process lines, structural piling where higher strength than X42 is needed, and bridge and construction supports. It is a versatile grade that balances strength, cost, and weldability, and it is often the economical alternative where X52 strength is not fully required.
Supplementary Requirements
For sour service, the pipe must comply with the applicable requirements of NACE MR0175 / ISO 15156, with hardness control and testing for hydrogen-induced cracking. For low-temperature service, supplementary Charpy impact testing is specified at the design temperature. The order should state the PSL level and any supplementary requirements, and the certificate documents the chemistry, mechanical results, and hydrostatic data.
Frequently Asked Questions
Q: What is the yield strength of API 5L X46?
The specified minimum yield strength is 46,000 psi (317 MPa) and the minimum tensile strength is 63,000 psi (435 MPa).
Q: What is the difference between X46 and X42?
X46 has about 10% higher yield strength, allowing a thinner wall or higher pressure for the same diameter, at a small material-cost premium.
Q: What sizes are available in SSAW?
Commonly from 508 mm to 2032 mm outside diameter, with walls from about 6 mm to 20 mm and lengths of 6, 12, or 18 metres.
Q: Is X46 available at PSL2?
Yes. PSL2 adds strength limits, a yield-to-tensile ratio cap, mandatory impact testing, tighter chemistry, and carbon-equivalent control.
Q: Can X46 SSAW be used for sour service?
Only with the sour-service supplementary requirements, including hardness control and hydrogen-induced cracking testing per NACE MR0175 / ISO 15156.
Q: What is X46 used for?
Moderate-pressure oil and gas lines, water mains, slurry lines, structural piling, and construction supports where X42 is too light and X52 is not needed.





