ASTM A500 is the standard specification for cold-formed welded and seamless carbon steel structural tubing in round, square, rectangular, and special shapes. Grade B is the most widely ordered grade in the family because it offers the best balance of strength, weldability, and cost for structural sections. This article covers what Grade B pipe is used for, the mechanical requirements that apply, and the limits that buyers must respect when selecting it.
What Does ASTM A500 Cover?
A500 governs hollow structural sections produced by cold forming from sheet or plate, joined by electric resistance welding, or produced seamless. It covers rounds with a specified outside circumference of 88 inches or less and shaped sections with a specified wall thickness of 1.000 inch or less. The standard includes Grades A, B, C, and D, where Grade D requires heat treatment after forming. Grade B is the default structural choice in most North American and export specifications.
Mechanical Properties of Grade B
Grade B requirements differ between round and shaped sections. Round tubing requires a minimum yield strength of 315 MPa, or 46 ksi, and a minimum tensile strength of 400 MPa, or 58 ksi. Square and rectangular sections require a minimum yield strength of 290 MPa, or 42 ksi, with the same 400 MPa minimum tensile strength. The lower shaped-section yield reflects the effect of cold forming at the corners and is a normal part of the specification, not a quality defect. Elongation minimums are about 23 percent for rounds and 25 percent for shapes in a 2-inch gauge length.
| Grade B Property | Round | Shaped (Square / Rectangular) |
|---|---|---|
| Minimum yield strength | 315 MPa (46 ksi) | 290 MPa (42 ksi) |
| Minimum tensile strength | 400 MPa (58 ksi) | 400 MPa (58 ksi) |
| Minimum elongation | 23 percent | 25 percent |
Chemical Composition
Grade B is a weldable carbon steel with typical maximum limits of carbon 0.26 percent, manganese 1.35 percent, phosphorus 0.035 percent, and sulfur 0.035 percent. When specified, a minimum copper content of 0.20 percent provides improved atmospheric corrosion resistance. The chemistry is controlled so that the cold-formed corners retain ductility and the longitudinal seam weld develops full strength.
Typical Applications
Grade B tubing appears in building structure support systems including columns and beams of steel-frame factories and high-rise frames, roof trusses, and space grid structures for stadiums and exhibition halls. In bridge engineering it is used for truss members, pier support structures, and pedestrian overpass components. In mechanical equipment it forms booms and chassis frames for cranes and excavators, conveyor roller frames, and machine tool guards. In auxiliary structures it is used for storage racking, solar panel support frames, signage structures, and temporary staging and exhibition frames.
Service Limits That Must Be Respected
A500 is a structural specification, not a pressure pipe specification. It is suitable for non-pressure fluid service such as drainage and agricultural irrigation only where the system is not pressure-rated. It must not be used for gas lines, flammable or explosive media, steam service, or high-temperature and high-pressure pipelines, which are covered by standards such as ASTM A53, A106, or API 5L. Structural integrity and building code compliance also require checking the actual loads against the section properties of the tubing.
Manufacturing and Forming
A500 tubing is cold formed from strip or plate into the required cross-section and joined by electric resistance welding along the longitudinal seam. Square and rectangular sections are formed through a series of rolls and a sizing mill, which sets the corner radii and flat-face dimensions. The cold-formed corners work-harden, which is why the strength requirements are defined separately for rounds and shapes.
Testing and Certification
Standard testing includes tensile tests on the base material, flattening tests for round tubing, crush tests for shaped tubing, and optional hydrostatic or non-destructive testing when agreed between buyer and supplier. Certification documents the heat number, chemistry, and mechanical test results. For structural projects, the mill certificate is usually required by the specifying engineer.
How to Order Grade B Tubing
Specify the standard and grade, for example ASTM A500 Grade B; the shape, round, square, or rectangular; the nominal size, wall thickness, and length; and any special requirements such as tension tests, copper-bearing steel, or third-party inspection. Example: ASTM A500 Grade B, square tubing 100 by 100 by 5 mm, 6 m lengths.
FAQ
What is the yield strength of A500 Grade B?
Round Grade B tubing has a 315 MPa minimum yield strength; square and rectangular Grade B sections have a 290 MPa minimum yield strength.
Can A500 Grade B pipe carry water or gas?
Only non-pressure service such as drainage is acceptable. A500 is structural tubing and must not be used for gas, steam, or pressurized fluid lines.
What is the difference between A500 Grade B and Grade C?
Grade C is stronger: rounds require 345 MPa minimum yield and shapes 317 MPa, with a higher tensile requirement, making it suitable for heavier loaded members at a slightly higher cost.
Is A500 the same as A53?
No. A53 covers pipe for mechanical and pressure applications including threaded ends, while A500 is dedicated to structural tubing in rounds and shapes with specific strength requirements.
Can A500 Grade B be welded to structural steel?
Yes. Grade B is designed for welding and is commonly joined to plates, beams, and other sections using standard structural welding processes such as SMAW, GMAW, or FCAW.





