Sep 28, 2025 Leave a message

JIS G3452 Carbon Steel Pipe

JIS G3452 Carbon Steel Pipe

JIS G 3452 is used for piping with relatively low working pressure, such as steam, water (except for water supply), oil, gas, air, etc.

Relevant Standard: KS D 3507, ASTM A 53 ,API 5L, DIN 2440 ,DIN2441, BS 1387 /BS 3601

 

Product Features:

Possessing adequate strength and corrosion resistance, galvanized pipes effectively prevent rust and extend service life. Their operating temperature range typically spans from -15°C to 350°C, meeting the requirements for conveying various low-pressure fluids.

 

JIS G3452 Carbon Steel Pipe Dimension:

Nominal diameter

Outside diameter (mm)

Tolerances on the outside diameter

Wall thickness

Tolerances on wall thickness Unit mass excluding socket

A

B

Pipes to be cut with a taper thread

Other pipes

mm

kg/m

6

1/8

10.5

±0.5mm

±0.5mm

2

+ Not specified
-12.5%

0.419

8

1/4

13.8

±0.5mm

±0.5mm

2.3

0.664

10

3/8

17.3

±0.5mm

±0.5mm

2.3

0.866

15

1/2

21.7

±0.5mm

±0.5mm

2.8

1.25

20

3/4

27.2

±0.5mm

±0.5mm

2.8

1.6

25

1

34

±0.5mm

±0.5mm

3.2

2.45

32

1 1/4

42.7

±0.5mm

±0.5mm

3.5

3.16

40

1 1/2

48.6

±0.5mm

±0.5mm

3.5

3.63

50

2

60.5

±0.5mm

±1%

3.8

5.12

65

2 1/2

76.3

±0.7mm

±1%

4.2

6.34

80

3

89.1

±0.8mm

±1%

4.2

8.49

90

3 1/2

101.6

±0.8mm

±1%

4.2

9.74

100

4

114.3

±0.8mm

±1%

4.5

12.2

125

5

139.8

±0.8mm

±1%

4.5

16.1

150

6

165.2

±0.8mm

±1%

5

19.2

175

7

190.7

±0.9mm

±1%

5.3

24.2

200

8

216.3

±1.0mm

±1%

5.8

30.4

225

9

241.8

±1.2mm

±1%

6.2

36

250

10

267.4

±1.3mm

±1%

6.6

41.2

300

12

318.5

±1.5mm

±1%

6.9

53.8

350

14

355.6

-

±1%

7.9

65.2

400

16

406.4

-

±1%

7.9

77.6

450

18

457.2

-

±1%

7.9

87.5

500

20

508

-

±1%

7.9

97.4

 

Production method:

The manufacturing method shall be as follows.

a) Pipes shall be manufactured by a combination of the pipe-making method and finishing method shown in Table 1. Symbols representing manufacturing methods shall be as shown in Table 1.

b) Pipes are normally as manufactured. Cold-finished tubes shall be annealed after manufacture.

c) Both ends of pipes with a nominal diameter of 300A or smaller in Table 4 shall have threaded or plain ends, and pipes with a nominal diameter of 350A or larger shall have plain ends. However, if the orderer specifies the bevel end, the shape shall be according to the agreement between the parties to delivery, and if there is no particular shape specified, it shall be as shown in Figure 1. Figure 1 - Shape of bevel end

d) When pipes are manufactured by electric resistance welding, external and internal weld beads shall be removed to smoothly follow the shape of the pipe unless otherwise specified. However, if it is difficult to remove the internal weld bead, it may be left as it is.

e) In the case of a threaded pipe, both ends shall be tapered according to JIS B 0203, and one joint according to JIS B 2301 or JIS B 2302 (hereinafter referred to as a socket) shall be screwed into one end. The unscrewed end of the socket shall be protected by a thread protection ring or other suitable means. However, if specified by the purchaser, the socket may be omitted. Inspection of tapered threads shall be in accordance with JIS B 0253.

f) Classification of galvanized shall be as per Table 1. If zinc plating is used, it shall be done before threads are machined into pipes and sockets. In this case, the black tubes and sockets that have passed the inspection are thoroughly cleaned by blasting, pickling, etc., and then galvanized by the hot-dip galvanizing method.

g) The zinc used for galvanizing shall be JIS H 2107 distilled, bare metal class 1, or zinc with equivalent or higher quality.

h) Other general matters for zinc plating shall be in accordance with JIS H 8641.

 

Application Areas:

Suitable for pipeline systems carrying low-pressure fluids such as water, air, steam, oil, and gases at working pressures below approximately 1 MPa, including flat heat exchangers and non-critical pipeline components. JIS G3452 Carbon Steel Pipe may also be applied to hot-dip galvanized pipes in accordance with JIS G3445. When used in conjunction with JIS G3461, it can further be applied to pipeline components such as boilers.

 

FAQ

What quality certification documents can be provided during procurement?
Product compliance certificates, material certificates MTC, third-party inspection reports, etc.

 

What is the delivery lead time?
Standard specifications (e.g., DN15~DN200): Ample stock available, delivery within 7-15 days after order placement; Custom production: 20-30 days lead time

 

How should quality issues (e.g., dimensional deviations, rust) with received pipes be addressed?

First, provide photos of the defective JIS G3452 Carbon Steel Pipe products, batch number, and quality documentation. We will respond within 24 hours.
If inspection confirms production-related defects, we offer unconditional returns or replacements and cover all logistics costs for both directions.

Hot Tags: jis g3452 carbon steel pipe,JIS G3452 SGP Galvanzied Pipe,JIS G3452 SGP,JIS G3452 Grade SGP

什么是无缝钢管,有哪些性能? - 无缝钢管价格-山东无缝钢管厂家-聊城荣贺金属制品

Send Inquiry