The JIS G 3429 Standard and the STH12 Grade
JIS G 3429 is the Japanese Industrial Standard titled Seamless Steel Tubes for High Pressure Service. It specifies requirements for dimensions, tolerances, mechanical properties and chemical composition of seamless tubes intended for high temperature and high pressure duty. The word seamless is central to the standard: these tubes are made without a longitudinal weld, so the wall is homogeneous around the circumference and there is no weld seam to act as a weak point in pressure containment or in high temperature service.
In the grade designation, STH stands for seamless tube for high pressure. The number 12 identifies the position of the grade in the carbon range covered by the standard, being a low carbon grade with good weldability and formability for the fabrication of complex boiler and heat exchanger assemblies.
Chemical Composition of STH12
| Element | Composition |
|---|---|
| Carbon (C) | 0.07 to 0.13% |
| Silicon (Si) | 0.10 to 0.50% |
| Manganese (Mn) | 0.40 to 0.80% |
| Phosphorus (P) | 0.035% max |
| Sulfur (S) | 0.035% max |
| Residual elements | Chromium, copper, nickel and molybdenum held to specified maximum limits |
The low carbon range is what gives STH12 its weldability: at these levels the heat affected zone of a welded joint does not develop the hard, crack sensitive structures that heavier carbon grades produce. Manganese and silicon provide the strength and deoxidation, while the tight phosphorus and sulfur limits keep the steel clean and improve toughness at temperature.
Mechanical Properties of STH12
| Property | Requirement |
|---|---|
| Minimum tensile strength | 380 MPa |
| Minimum yield strength | 205 MPa |
| Minimum elongation | 30% |
| Typical tests | Tensile, flattening, flaring, bend and hydrostatic or non-destructive electric test |
| Dimensional regime | Outside diameter and wall thickness with tolerances set by the standard |
The elongation requirement of 30% is characteristic of a low carbon, ductile tube grade and is what allows tubes to be bent, expanded into tube sheets and cold formed during boiler fabrication without cracking.
Why STH12 Is Chosen for High Pressure Service
Seamless construction gives a continuous wall with no longitudinal weld to inspect or to weaken under pressure.
Controlled low carbon chemistry gives good weldability and formability for boiler and heat exchanger fabrication.
Reliable strength and ductility at elevated temperature support predictable pressure design.
Good resistance to oxidation and scaling in the presence of combustion gases extends service life.
Stable properties across the operating cycle, which matters where equipment is started and stopped repeatedly.
Typical Applications
STH12 tubes are used almost exclusively in critical high temperature and high pressure equipment. That includes boiler wall tubes where water is heated to steam, superheater and reheater tubes where steam is raised to a higher temperature, heat exchanger and condenser tubes where heat passes from one medium to another under pressure, and process piping in chemical, refining and power generating plants. Because the tubes operate under pressure at temperature, the material is normally ordered with a full test certificate and dimensions controlled to the standard.
Equivalent and Comparable Grades
| Standard | Comparable grade |
|---|---|
| ASTM A179 / ASME SA179 | A179 heat exchanger tube |
| DIN 17175 | St35.8 |
| GB/T 3087 | 20 and 20G boiler tube grades |
These grades are functionally comparable, but they are not identical. Chemical limits, heat treatment requirements, testing procedures and dimensional tolerances can differ between standards, so a substitution in a boiler or pressure component should always be assessed against the design code and the original specification rather than by grade name alone.
Fabrication, Inspection and Common Pitfalls
STH12 tube is welded by gas tungsten arc for the root pass and shielded metal arc, gas metal arc or submerged arc for subsequent passes, with filler metal matched to the base metal strength. Tube ends are prepared by machining or grinding to the required weld profile, and cold bending or expanding is carried out within the limits set by the standard. Field and shop joints are normally stress relieved where the design code or wall thickness requires it.
Supplying welded tube where the standard requires seamless product.
Accepting a certificate that does not show chemical, tensile, elongation and hydrostatic test results.
Substituting a comparable grade without checking the elevated temperature data required by the design.
Ignoring the specified tolerance regime when tubes are expanded into tube sheets.
Storing or handling tube without end caps, which allows contamination of the bore.
FAQ
Q: What is JIS G3429 STH12?
It is a seamless carbon steel tube grade specified in JIS G 3429, the Japanese standard for seamless steel tubes for high pressure service. It is used for boiler, superheater and heat exchanger tubes operating at elevated temperature.
Q: What does STH stand for?
The letters identify seamless tube for high pressure, and the number 12 indicates a low carbon grade with a nominal carbon range of 0.07 to 0.13%, chosen for weldability and ductility.
Q: What are the mechanical properties of STH12?
The standard requires a minimum tensile strength of 380 MPa, a minimum yield strength of 205 MPa and a minimum elongation of 30%. Tubes are also subject to flattening, flaring, bend and hydrostatic or non-destructive electric testing.
Q: Is STH12 the same as ASTM A179?
They are close equivalents and both are used for heat exchanger and boiler tube service. The chemical limits and testing requirements are not identical, so the specification called for by the project should be ordered.
Q: Can STH12 pipe be welded?
Yes. Its low carbon content gives good weldability. Normal practice is gas tungsten arc welding for the root pass with a matched filler metal and controlled heat input, followed by filler passes by shielded metal arc, gas metal arc or submerged arc welding.
Q: Why is seamless construction required for high pressure service?
Because the wall has no longitudinal weld, there is no seam to provide a preferential path for leakage or a region of altered properties. This gives more predictable pressure containment and durability at high temperature.





