Nouns related to mechanical properties of steel
1. Yield point (σ s )
When the steel or sample is stretched, when the stress exceeds the elastic limit, even if the stress no longer increases, the steel or sample continues to undergo significant plastic deformation. This phenomenon is called yielding, and the minimum stress value when yielding occurs is for the yield point. Assume Ps is the external force at the yield point s, Fo is the cross-sectional area of the sample, then the yield point σ s =Ps/Fo(MPa), MPa is called MPa, which is equal to N (Newton)/mm2, (MPa=106Pa, Pa: Pascal=N/m2)
2. Yield strength (σ 0.2)
The yield point of some metal materials is extremely unclear and difficult to measure. Therefore, in order to measure the yield characteristics of the material, the stress when the permanent residual plastic deformation is equal to a certain value (usually 0.2% of the original length) is specified, which is called the condition. Yield strength or simply yield strength σ 0.2.
3. Tensile strength (σ b )
The maximum stress value reached by the material from the beginning to the time of fracture during the stretching process. It indicates the steel's ability to resist fracture. Corresponding to tensile strength are compressive strength, flexural strength, etc.
Assuming that Pb is the maximum tensile force reached before the material is broken, Fo is the cross-sectional area of the sample, then the tensile strength σ b = Pb/Fo (MPa).
4. Elongation (δ s )
After the material is pulled apart, the percentage of its plastic elongation length to the original sample length is called elongation or elongation.

5. Yield-strength ratio (σ s/ σ b )
The ratio of the yield point (yield strength) of steel to its tensile strength is called the yield ratio. The larger the yield ratio, the higher the reliability of structural parts. Generally, the yield ratio of carbon steel is 0.6-0.65, that of low alloy structural steel is 0.65-0.75, and that of alloy structural steel is 0.84-0.86.
6. Hardness
Hardness indicates a material's ability to resist hard objects pressing into its surface. It is one of the important performance indicators of metal materials. Generally, the higher the hardness, the better the wear resistance. Commonly used hardness indicators include Brinell hardness, Rockwell hardness and Vickers hardness.
⑴ Brinell hardness (HB)
Press a hardened steel ball of a certain size (usually 10mm in diameter) into the surface of the material with a certain load (usually 3000kg) and keep it for a period of time. After the load is removed, the ratio of the load to its indentation area is the Brinell hardness value ( HB), unit is kilogram force/mm2 (N/mm2).

⑵Rockwell hardness (HR)
When HB>450 or the sample is too small, Brinell hardness test cannot be used and Rockwell hardness measurement is used instead. It uses a diamond cone with a vertex angle of 120° or a steel ball with a diameter of 1.59 or 3.18mm to press into the surface of the material to be tested under a certain load, and the hardness of the material is calculated from the depth of the indentation. According to the different hardness of the test material, it is expressed in three different scales:
HRA: The hardness is obtained using a 60kg load and a diamond cone intruder, and is used for extremely hard materials (such as cemented carbide, etc.).
HRB: is the hardness obtained by using a 100kg load and a hardened steel ball with a diameter of 1.58mm. It is used for materials with lower hardness (such as annealed steel, cast iron, etc.).
HRC: The hardness is obtained using a 150kg load and a diamond cone intruder, and is used for materials with very high hardness (such as quenched steel, etc.).
⑶Vickers hardness (HV)
Use a diamond square cone intruder with a load within 120kg and a vertex angle of 136° to press into the material surface. Divide the surface area of the material indentation pit by the load value, which is the Vickers hardness value (HV)





