Sep 16, 2025 Leave a message

Introduction to Q235C Steel Pipe

Q235C is a common carbon structural steel grade under the Chinese standard GB/T 700. The "Q" denotes the yield strength, "235" indicates the minimum yield strength of 235 MPa at a thickness of ≤16mm, and the "C" represents the quality grade, which dictates impact toughness and chemical composition control.

Pipes made from Q235C are typically manufactured according to standards like GB/T 8162 (for structural seamless pipes) or GB/T 8163 (for seamless pipes for fluid transmission). They are widely used in various structural applications, frames, and for conveying non-critical fluids where good weldability and moderate strength are required, along with better low-temperature toughness than Q235A or Q235B grades.


Key Product Parameters & Characteristics

1. Chemical Composition (Melting Analysis)

The chemical composition is a key factor in the weldability and mechanical properties of the steel.

 
 
Element Content (%) (Standard Requirement) Typical Value (%)
Carbon (C) ≤ 0.18 0.12 - 0.18
Manganese (Mn) ≤ 1.40 0.35 - 0.65
Silicon (Si) ≤ 0.35 0.20 - 0.35
Sulfur (S) ≤ 0.035 0.025 - 0.035
Phosphorus (P) ≤ 0.035 0.025 - 0.035
De-oxidation Method Killed Steel (Fully deoxidized)  

Note: The steel must be fully killed (e.g., silicon-killed or aluminum-killed), which provides a more homogeneous structure and better impact properties.

2. Mechanical Properties

These properties define the steel's behavior under load. Tested on the base material of the pipe.

 
 
Property Standard Requirement Value / Description
Yield Strength (ReH) ≥ 235 MPa ~235-275 MPa (Varies with wall thickness)
Tensile Strength (Rm) 375 - 500 MPa ~375-460 MPa
Elongation at Break (A) ≥ 25% (for thickness 40-60mm) Typically ~26-32%
Impact Energy (KV2) ≥ 27 J at 0°C (32°F) Tested longitudinally at 0°C on Charpy V-notch specimens. This is the key difference from Q235B (tested at 20°C) and Q235A (no requirement).

3. Dimensional Specifications (GB/T 8162/8163)

Q235C pipes are available in a wide range of sizes.

 
 
Parameter Common Range Standard Specifications
Outer Diameter (OD) 10 mm - 660 mm (and larger) Governed by the pipe standard (e.g., GB/T 8162)
Wall Thickness (WT) 1.0 mm - 60 mm (and thicker) Governed by the pipe standard
Length Usually 6m, 12m, or Random Fixed Length (6m/12m) or Random Length (RLL)

4. Technological Properties

 
 
Property Performance
Weldability Excellent. Q235C is very easy to weld using all common methods (SMAW, GMAW, etc.). No pre-heating is required for most thicknesses.
Bending/Forming Good. It has good ductility and can be cold formed easily.
Machinability Good. Typical machinability rating for carbon steel.

Comparison Table of Q235 Grades

This table highlights the difference between Q235A, B, and C.

 
 
Feature Q235A Q235B Q235C
Impact Test Not Required Required at +20°C (68°F) Required at 0°C (32°F)
Impact Energy (min) - ≥ 27 J ≥ 27 J
S (Sulfur) Max 0.050% 0.045% 0.040% [Often 0.035%]
P (Phosphorus) Max 0.045% 0.045% 0.040% [Often 0.035%]
De-oxidation F, Z Z Z (Killed Steel)
Typical Application General structures with no impact requirement General structures at ambient temperature Structures requiring better low-temperature toughness

Legend: F = Rimmed steel, Z = Killed steel.


Equivalent Grades (Approximate)

It's crucial to note that no grade is a perfect equivalent due to differences in national standards. However, these grades are often used for similar applications.

 
 
Standard Approximate Equivalent / Comparable Grade
ISO Fe360C (ISO 630) - Obsolete, but similar in concept.
Europe (EN) S235J2 (EN 10025-2) - Tested at -20°C, so it's generally superior to Q235C.
USA (ASTM) ASTM A36 - Similar strength, but A36 has different chemical rules and is not impact-tested by default. Grade B of standards like ASTM A53 or ASTM A106 has higher strength but is a closer functional match for piping.
Japan (JIS) SS400 - Similar strength, but SS400 has no guaranteed impact property.

Applications of Q235C Steel Pipes

Structural frameworks and supports

Conveying rollers in machinery

General fluid transmission (water, air, oil) in non-critical services

Construction and agricultural equipment

Furniture and decorative structures

Important Note:

When ordering or specifying Q235C pipe, it is essential to define both the material standard (GB/T 700) and the pipe manufacturing standard (e.g., GB/T 8162 or 8163) to ensure all dimensional tolerances, testing, and delivery conditions are clearly understood.

info-275-183info-259-194info-264-191

Send Inquiry