API 5CT N80 is a very common and versatile grade of steel pipe used in the oil and gas industry for both casing and tubing. It is defined by the American Petroleum Institute (API) specification 5CT.
The "N" stands for a strength level based on its minimum yield strength, and the "80" denotes a minimum yield strength of 80,000 psi (80 ksi). It offers a good balance of strength, ductility, and cost-effectiveness, making it suitable for a wide range of well depths and conditions, though it is not recommended for sour service (environments containing hydrogen sulfide, H₂S) without special requirements.
Key Product Parameters
Grade Designation: N80
Type: There are two main types within the N80 grade:
N80-1: The standard quality grade.
N80-Q: Manufactured using the Quench and Temper (Q&T) heat treatment process. This provides better mechanical properties, particularly impact toughness, and is more common for critical applications.
Mechanical Properties:
Minimum Yield Strength (YS): 80,000 psi (552 MPa)
Maximum Yield Strength: 110,000 psi (758 MPa)
Minimum Tensile Strength (TS): 100,000 psi (689 MPa)
Hardness (typical): Maximum is usually specified to ensure resistance to Sulfide Stress Cracking (SSC) if needed, but standard N80 is not inherently SSC-resistant. For application in sour service, special requirements like N80 Type 1 with a maximum hardness of 22 HRC may apply.
Chemical Composition (typical, % by weight):
The API 5CT standard specifies maximum limits for elements like Phosphorus (P) and Sulfur (S) to ensure quality, but it does not mandate a specific chemical composition. This allows manufacturers flexibility. A typical chemistry for N80-Q is:
Carbon (C): 0.20 - 0.35%
Manganese (Mn): 1.00 - 1.60%
Phosphorus (P): ≤ 0.025% (max)
Sulfur (S): ≤ 0.015% (max)
Other elements like Silicon (Si), Chromium (Cr), Molybdenum (Mo) may be added based on the manufacturer's process.
Tables of Specifications
Table 1: Standard Dimensional Specifications (API 5CT)
(This is an example for common sizes. API 5CT covers a much wider range.)
| Outside Diameter (OD) | Weight (lb/ft) | Wall Thickness (in) | Drift Diameter (in) |
|---|---|---|---|
| 4-1/2" (114.3 mm) | 9.50 | 0.271 | 3.965 |
| 4-1/2" (114.3 mm) | 11.60 | 0.337 | 3.826 |
| 5-1/2" (139.7 mm) | 14.00 | 0.304 | 4.892 |
| 5-1/2" (139.7 mm) | 17.00 | 0.375 | 4.750 |
| 7" (177.8 mm) | 20.00 | 0.272 | 6.456 |
| 7" (177.8 mm) | 26.00 | 0.362 | 6.276 |
| 9-5/8" (244.5 mm) | 36.00 | 0.352 | 8.921 |
| 9-5/8" (244.5 mm) | 40.00 | 0.395 | 8.835 |
Note: Drift diameter is the minimum guaranteed internal diameter to ensure downhole tools can pass through.
Table 2: Mechanical Properties Summary
| Property | Value (Imperial) | Value (Metric) | Note |
|---|---|---|---|
| Yield Strength (Min) | 80,000 psi | 552 MPa | |
| Yield Strength (Max) | 110,000 psi | 758 MPa | |
| Tensile Strength (Min) | 100,000 psi | 689 MPa | |
| Hardness (typical) | ~ 22 HRC (max) | ~ 22 HRC (max) | For potential sour service conditions |
| Elongation (Min) | Varies with size | Varies with size | As per API 5CT formula |
Applications and Limitations
| Feature | Description |
|---|---|
| Primary Applications | - Intermediate Casing: Isolating unstable formations or weak zones. - Production Casing/Tubing: In sweet (non-sour) oil and gas wells. - Surface Casing: For deeper wells where higher strength than J55/K55 is needed. |
| Key Advantages | - High Strength-to-Weight Ratio: Good for medium-depth wells. - Cost-Effective: Widely available and competitively priced. - Good Weldability and Ductility. |
| Limitations | - Not for Sour Service: Standard N80 is susceptible to Sulfide Stress Cracking (SSC) in H₂S environments. For mild sour service, N80 Type 1 (with strict hardness control) may be used, but L80 is generally the preferred choice for sour service. - Lower Strength than P110/Q125: Not suitable for ultra-deep or high-pressure wells where higher grades are required. |
Comparison with Other Common Grades
| Grade | Min. Yield Strength (psi) | Typical Use Case | Key Difference from N80 |
|---|---|---|---|
| J55 | 55,000 | Shallow wells, surface casing | Lower strength, lower cost. |
| L80 | 80,000 | Sour service (H₂S environments) | Similar strength, but SSC-resistant. |
| P110 | 110,000 | Deep, high-pressure wells | Higher strength, but more brittle and not for sour service. |
In summary, API 5CT N80 is a versatile, medium-strength workhorse grade for the oilfield. Its parameters make it ideal for a broad spectrum of standard well applications, but careful consideration must be given to environmental conditions like the presence of H₂S.








