

Quick Summary
ST45 is a non-alloy quality carbon steel material grade used for seamless pipes and tubes, primarily defined by the DIN 1629 standard (which has been largely superseded by the European EN 10216-1 standard). It is a general-purpose steel used for low-pressure applications and is not suitable for welding under most standards.
1. Material Standard and Equivalent Grades
ST45 is most famously associated with the old German standard DIN 1629 Part 4. The modern European standard that replaces it is EN 10216-1, which designates this grade as P235TR1.
Here are the key equivalent grades from different standards:
| Standard | Equivalent Grade | Note |
|---|---|---|
| DIN 1629 | ST45 | The original, now largely historical designation. |
| EN 10216-1 | P235TR1 | The modern European standard replacement. |
| ASTM A53 | Grade A | A very close, commonly used American equivalent. |
| JIS G3454 | STPG 38 | Japanese equivalent. |
| GB/T 8163 | 10# (10 Steel) | Chinese equivalent. |
2. Chemical Composition
ST45 is a low-carbon steel. Its mechanical properties are more critical than its precise chemical composition. A typical composition is:
| Element | Content (%) |
|---|---|
| Carbon (C) | ≤ 0.21 |
| Manganese (Mn) | ≤ 0.70 |
| Phosphorus (P) | ≤ 0.040 |
| Sulfur (S) | ≤ 0.040 |
| Silicon (Si) | ≤ 0.35 |
Key Takeaway: The low carbon content makes it relatively easy to machine and form, but it also means it has low hardenability and is not recommended for welding in pressure applications. If welding is absolutely necessary, pre-heat and post-weld heat treatment may be required, but it's generally avoided.
3. Mechanical Properties
The "ST45" name gives a clue to its properties. The number "45" refers to the minimum tensile strength in kgf/mm².
| Property | Value |
|---|---|
| Tensile Strength (Rm) | 440 - 540 MPa (≈ 45 - 55 kgf/mm²) |
| Yield Strength (Rp0.2), min. | 255 MPa (min.) |
| Elongation (A), min. | ~25% (varies with wall thickness) |
4. Key Characteristics and Advantages
Good Machinability: Its low carbon content makes it relatively easy to cut, drill, and machine.
Good Formability: It can be bent and formed without cracking easily.
Cost-Effective: As a basic carbon steel, it is one of the most economical options for non-critical applications.
Weldability (with caution): While not recommended for pressure welds, it can be welded for structural or non-critical applications with proper technique.
5. Limitations and Disadvantages
Low Strength: It has lower mechanical strength compared to higher-grade carbon and alloy steels.
Poor Weldability for Pressure: It is not suitable for welded pressure applications according to most international pressure vessel and piping codes (like ASME B31.1/B31.3). The heat-affected zone (HAZ) of a weld can become brittle.
Low Temperature Brittleness: It becomes brittle at low temperatures and is not suitable for low-temperature service.
Limited Corrosion Resistance: Like all carbon steels, it rusts easily in the presence of water and oxygen and requires coating or painting for corrosion protection.
6. Common Applications
Due to its limitations with welding and pressure, ST45 / P235TR1 pipes are typically used for:
Low-pressure fluid transportation (e.g., water, air, oil, gas).
Structural applications and mechanical parts where pressure is not a factor.
Bearing sleeves and bushings.
Automobile and tractor parts.
General engineering purposes.
Important Note on Welding
This is the most critical point to remember: While you might find ST45 pipe being welded in workshops, it is explicitly forbidden for use in welded pressure systems under most modern codes. If a project requires a welded carbon steel pipe for pressure service, a properly weldable grade like ASTM A106 Grade B or API 5L Grade B (which have controlled carbon content and are killed steels) should be specified instead.
Conclusion
Grade ST45 Carbon Steel Pipe is a general-purpose, economical material suitable for low-pressure and structural applications where welding is not required for pressure containment. For any critical application, especially involving pressure or welding, it is essential to consult the relevant, up-to-date engineering standards (like EN 10216-1 or ASTM A53/A106) and specify the appropriate, weldable grade.





