

EN 10217 S275 Pressure Pipe
Note: S275 is a structural steel grade designation per EN 10025, not typically a grade for pressure tubes per EN 10217. This indicates a potential mix-up in specification.
EN 10217 uses a "P" prefix for pressure tube grades (e.g., P235, P265).
EN 10219 (for structural hollow sections) uses "S" prefix grades like S235, S275, S355.
However, if referring to a pressure tube made from steel with S275-grade properties, it would likely align with EN 10217-1 P265 or similar.
Correct Grade Mapping for Pressure Application
| Intended "S275" | Closest EN 10217 Grade | Key Rationale |
|---|---|---|
| Yield Strength ~275 MPa | P265 (Min YS = 265 MPa) | Nearest match. P265 is the standard grade for this strength level in pressure tubing. |
| General Purpose | EN 10217-1: Welded tubes, non-alloy steel | The correct part for standard ERW carbon steel pressure tubes. |
| Elevated Temp Service | EN 10217-2: P265TR1 or P265TR2 | If service is above room temperature (up to 300°C or 450°C). |
EN 10217-1 P265 ERW Pipe Specification
Mechanical Properties
| Property | Requirement for P265 |
|---|---|
| Minimum Yield Strength (ReH) | 265 MPa (~38,400 psi) |
| Tensile Strength (Rm) | 410 - 570 MPa |
| Minimum Elongation (A) | 22% (based on test piece geometry) |
Chemical Composition (Maximum %)
| Element | P265 |
|---|---|
| Carbon (C) | 0.20 |
| Manganese (Mn) | 1.20 |
| Phosphorus (P) | 0.025 |
| Sulfur (S) | 0.020 |
| Silicon (Si) | 0.35 (if killed steel) |
Manufacturing & ERW Process
Process: High-Frequency (HF) Electric Resistance Welding.
Material: Continuously cast, fine grain killed steel strip/plate.
Weld Treatment: Weld seam may be heat-treated (normalized) to match base metal properties, especially for critical applications.
Testing: Mandatory 100% non-destructive testing of the weld seam (Eddy Current or Ultrasonic).
Standard Dimensions (Typical ERW Range)
Outside Diameter: 21.3 mm to 610 mm (≈ 1/2" to 24")
Wall Thickness: 2.0 mm to 25.0 mm
Lengths: Random or specified cut lengths up to 24m.
Key Tests & Inspection (EN 10217-1)
Hydrostatic Test or NDE Alternative: Proof of leak tightness.
Weld Seam NDE: 100% of weld length by Eddy Current (EN ISO 10893-5) or Ultrasonic (EN ISO 10893-10).
Transverse Tensile Test: On finished tube across the weld.
Flattening Test: On a ring sample across the weld to verify ductility.
Visual & Dimensional Inspection: Per EN 10246 series.
Common Applications
Process piping for water, steam, air, and non-aggressive gases/liquids.
Boiler and heat exchanger tubing (with appropriate temperature grade).
Hydraulic systems.
General mechanical and pressure applications.
Comparison: S275 (Structural) vs. P265 (Pressure)
| Aspect | S275JR (EN 10025 / EN 10219) | P265 (EN 10217-1) |
|---|---|---|
| Primary Use | Structural (columns, beams, frames) | Pressure Containment |
| Standard Focus | Mechanical properties, weldability for construction. | Pressure integrity, leak-tightness, elevated temp properties. |
| Key Test | Tensile, bend, impact (Charpy). | Hydrostatic/NDE, 100% weld seam inspection, flattening test. |
| Chemical Control | Less strict on S/P (e.g., S≤0.035%). | Stricter (S≤0.020%, P≤0.025%) for better formability & integrity. |
| Certification | Certificate 2.2 or 3.1 may be sufficient. | Usually requires Inspection Certificate 3.1.B per EN 10204. |





