What EN 10216-5 Covers
EN 10216 is the European standard for seamless steel tubes for pressure purposes, issued in parts by steel type. Part 5 covers stainless steel tubes and sets out the technical delivery conditions: steel grades and their chemical composition, delivery conditions, mechanical properties at room and elevated temperature, tolerances on dimensions and mass, and the test category that determines how the tubes are examined before delivery. Tubes ordered to EN 10216-5 are seamless, so there is no longitudinal weld and no weld-related inspection category.
The purchaser specifies the outside diameter and wall thickness, the delivery condition, and the test category. The test category decides whether the non-destructive examination demanded by the standard is applied on a per-tube or a lot basis, together with the leak-tightness test. Specifying the category correctly at the enquiry stage avoids both unnecessary cost and an under-inspected delivery.
Grade 1.4401 and Its Equivalents
1.4401 is the steel number for X5CrNiMo17-12-2, the standard molybdenum-bearing austenitic stainless steel. It is the European equivalent of UNS S31600 and of the TP316 grades of ASTM A312 and ASTM A269 for pipe and tube, and it is also covered as a sheet and plate grade by EN 10088-1 and ASTM A240.
| Element | EN 10088-1 / EN 10216-5, % | ASTM A240 TP316, % |
|---|---|---|
| Carbon | 0.07 max | 0.08 max |
| Silicon | 1.00 max | 0.75 max |
| Manganese | 2.00 max | 2.00 max |
| Phosphorus | 0.045 max | 0.045 max |
| Sulfur | 0.030 max | 0.030 max |
| Chromium | 16.5–18.5 | 16.0–18.0 |
| Nickel | 10.0–13.0 | 10.0–14.0 |
| Molybdenum | 2.00–2.50 | 2.00–3.00 |
| Nitrogen | 0.10 max | – |
The chromium content builds the passive oxide film that makes the steel stainless, the nickel stabilises the austenitic structure and provides ductility and toughness at low temperature, and the molybdenum is present specifically to improve resistance to pitting and crevice attack in chloride environments. On the usual pitting resistance formula, Cr + 3.3 Mo + 16 N, the grade gives a value in the region of 24 to 25, which is a useful step above the molybdenum-free 1.4301 grade.
Mechanical Behaviour and Temperature Limits
Tubes are normally supplied in the solution annealed condition. In that condition the room temperature requirements are a minimum 0.2 % proof strength of about 200 MPa and a tensile strength in the region of 500 to 700 MPa with an elongation of 35 % or better, values that are tabulated together with the elevated temperature proof strengths in the standard. Because the austenitic structure is not dependent on a quench-and-temper microstructure, the grade does not become brittle at low temperature and retains useful toughness down to cryogenic levels, which makes it a candidate for cold service as well as hot service.
At high temperature the material retains good strength and oxidation resistance. For continuous or intermittent high-temperature service the oxidation limit is usually quoted around 870 °C for intermittent exposure, while the permissible design stresses for pressure service are taken from the elevated temperature values given in the standard rather than from the oxidation limit. Long-term exposure in the sensitising range should be avoided for welded components unless a stabilised or low-carbon grade is used.
Applications
Chemical and petrochemical plants: process piping, reactors and heat exchangers handling acids, solvents and other corrosive fluids.
Oil and gas: flow lines, injection lines and utility services, including offshore platforms where chloride pitting resistance is essential.
Food, beverage and pharmaceutical: hygienic process piping for ingredients, cleaning agents and high-purity water, where a polished, easily cleaned, non-reactive surface is required.
Power generation: cooling water, boiler feedwater and auxiliary systems in conventional and nuclear plants.
Marine and shipbuilding: sea water, ballast and firefighting lines exposed to a chloride-rich atmosphere.
Building services: water supply in coastal areas, underfloor heating and hydraulic systems where long life without maintenance is valued.
Fabrication and Quality Control
1.4401 is readily welded by the common arc processes, and no post-weld heat treatment is required for the austenitic structure. A matching or slightly over-alloyed filler is normally selected; where the joint will not be solution annealed after welding, a low-carbon filler is preferred for its resistance to sensitisation. Clean stainless handling practice matters more than for carbon steel: dedicated brushes and grinding discs, no carbon steel contact, and removal of all contamination before pickling and passivation in accordance with ASTM A380 and ASTM A967.
The delivery inspection package typically combines dimensional verification, tensile and hardness testing, flattening or bend testing where specified, intergranular corrosion testing where the order calls for it, hydrostatic or eddy current leak-tightness testing according to the test category, and positive material identification on the finished tubes. Surface finish, straightness and end preparation are checked against the order, and the mill certificate is issued with the heat number traceable to the tubes supplied.
During selection, 1.4401 is often compared with 1.4301 on the one hand and duplex grades on the other. The molybdenum-bearing grade costs more than 1.4301 but survives chloride service that 1.4301 will not, and it remains easier to form and weld than the duplex alternatives, which is why it continues to be the default choice for general corrosive pressure piping.
FAQ
Q: What is the difference between EN 10216-5 1.4401 and ASTM A312 TP316?
They describe the same stainless steel in two standard systems. 1.4401 is the European steel number for X5CrNiMo17-12-2, and UNS S31600 is the American designation; the allowable composition ranges differ slightly between EN 10088-1 and ASTM A240, so the applicable standard must be stated on the order.
Q: Is 1.4401 pipe seamless or welded?
EN 10216-5 covers seamless tubes only. For welded stainless pressure tube, the corresponding European standard is EN 10217-7, so a requirement for a longitudinal weld must be ordered against that standard instead.
Q: Why is molybdenum added to this grade?
Molybdenum increases resistance to pitting and crevice corrosion in chloride-bearing environments. That is the main reason 1.4401 is selected over the molybdenum-free 1.4301 grade for sea water, de-icing salt and many chemical duties.
Q: Does 1.4401 pipe need post-weld heat treatment?
No. The austenitic structure is stable at ambient temperature, so welded joints are used in the as-welded condition. Cleaning, pickling and passivation of the weld and heat tint are required, but a post-weld heat treatment is not.
Q: What does the test category in EN 10216-5 mean?
It defines the extent of non-destructive examination and leak-tightness testing applied before delivery. Selecting the correct category at the enquiry stage fixes both the inspection cost and the quality documentation that will accompany the tubes.
Q: Can 1.4401 be used at low temperature?
Yes. The austenitic structure retains ductility and impact toughness at very low temperatures, so the grade is used in cold and cryogenic service as well as at elevated temperature, unlike ferritic or martensitic stainless grades.





