Nov 06, 2025 Leave a message

DIN 1629 Carbon Steel Pipe

info-300-168info-225-225

1. Key Overview & Replacement

Original Title: Seamless circular steel tubes for pressure purposes; technical delivery conditions.

Current Status: Withdrawn and replaced by EN 10216-1:2013.

Why it's still relevant: The material grades from DIN 1629 (like St 37.0, St 44.0, etc.) were directly carried over into EN 10216-1, and pipes ordered to this standard are now manufactured and tested according to EN 10216-1. It remains a common shorthand for specifying a certain quality of seamless carbon steel pressure tube.

2. Main Applications

DIN 1629/EN 10216-1 pipes are designed for applications involving pressure and high temperatures. Common uses include:

Boiler Tubes: For steam boilers and pressure vessels.

Heat Exchangers: For shells, tubesheets, and heat exchanger tubes.

Power Generation: Piping systems in fossil fuel and nuclear power plants.

Process Industries: For conveying fluids, steam, and gases under pressure in chemical, petrochemical, and oil & gas industries.

High-Temperature Service: General mechanical and structural applications under elevated temperatures and pressures.

3. Common Material Grades

The standard defined several grades based on their minimum yield strength (the first number) and their impact toughness (the suffix).

St 37.0: Minimum yield strength of 235 MPa. Good weldability and formability.

St 44.0: Minimum yield strength of 275 MPa. Higher strength than St 37.0.

St 52.0: Minimum yield strength of 355 MPa. A high-strength carbon steel.

Understanding the Nomenclature:

St: Stands for "Steel" (Stahl in German).

37, 44, 52: Represents the minimum yield strength in kgf/mm² (e.g., 37 kgf/mm² ≈ 355 N/mm² or MPa).

.0: The suffix indicates the testing group and impact energy requirements.

.0: No impact energy (Charpy V-notch) test required.

.2: Impact energy tested at +20°C.

.3: Impact energy tested at 0°C.

In the modern EN 10216-1 standard, these are designated as P235GH, P265GH, and P355GH respectively. The "P" stands for "Pressure," the number is the minimum yield strength in MPa, and the "H" stands for "High Temperature."

4. Key Specifications

The following table summarizes the main specifications as per the original DIN 1629 and its modern equivalent.

Feature DIN 1629 Specification Modern EN 10216-1 Equivalent
Type Seamless (mandrel rolled) Seamless
Manufacturing Hot-finished Hot-finished or cold-finished
Steel Type Non-alloy quality carbon steel Non-alloy quality steel
Common Grades St 37.0, St 44.0, St 52.0 P235GH, P265GH, P355GH
Testing Pressure test, tensile test, flattening test, etc. Non-destructive testing, tensile test, impact test (if specified), etc.

5. Chemical Composition (Typical % by Weight)

The composition is controlled to ensure weldability and strength.

Grade EN 10216-1 Equivalent C (max) Si (max) Mn P (max) S (max)
St 37.0 P235GH 0.16 0.35 0.40 - 1.20 0.025 0.020
St 44.0 P265GH 0.20 0.40 0.40 - 1.20 0.025 0.020
St 52.0 P355GH 0.22 0.55 1.10 - 1.70 0.025 0.020

Note: These are typical values; exact limits can vary. N, Cu, and other elements may also be restricted.

6. Mechanical Properties (at Room Temperature)

Grade EN 10216-1 Equivalent Yield Strength (min) [MPa] Tensile Strength [MPa] Elongation (min)
St 37.0 P235GH 235 360 - 480 25%
St 44.0 P265GH 265 410 - 530 24%
St 52.0 P355GH 355 470 - 630 22%

Comparison with Other Standards

DIN 1629 / EN 10216-1 pipes are closely comparable to other international standards for seamless pressure tubes:

ASTM A106 Gr B: The most common American equivalent for high-temperature service.

ASTM A53 Gr B: Another common US standard, but often used for lower temperatures and pressures than A106.

API 5L Gr B: Primarily for pipeline transportation in the petroleum and natural gas industries.

While the chemistries and mechanical properties are similar, the testing, certification, and specific application ranges can differ. Always consult the specific standard for critical applications.

Summary

When you hear "DIN 1629 pipe," it typically refers to a high-quality, seamless carbon steel pipe suitable for pressure and high-temperature applications. While the DIN standard itself is obsolete, its requirements live on in EN 10216-1, and its material grades (St 37.0, St 44.0, St 52.0) remain a universal language in engineering and procurement for this type of product. For any new project, specifications should reference EN 10216-1.

Send Inquiry