Mar 04, 2024 Leave a message

Cold Drawing vs Hot Rolling of Seamless Steel Pipe: Process Comparison

What Cold Drawing and Hot Rolling Mean in Seamless Pipe Production

Every seamless pipe begins as a solid round billet that is heated and pierced into a hollow shell. What happens after piercing decides whether the finished product is classified as hot rolled or cold drawn. In hot rolling the shell is rolled on a mandrel mill, plug mill, continuous rolling train or extrusion press while the steel is still above its recrystallisation temperature. In cold drawing the hot rolled shell is pickled to remove scale, coated with a phosphate and lubricant film, and then pulled at ambient temperature through a die over a plug or mandrel.

Hot rolled pipe is normally supplied in the condition defined by GB/T 8163, GB/T 3087 or ASTM A106, while cold drawn and cold rolled tube is ordered to GB/T 3639, ASTM A179, ASTM A192 or EN 10216-1 according to service. The process route therefore controls not only the dimensional class of the product but also the delivery condition, the mechanical property range and the price level.

Process Routes Compared

Stage Hot rolled route Cold drawn route
Feedstock Cut and centred round billet Hot rolled shell, ends trimmed and inspected
Forming temperature Above recrystallisation temperature after reheating Ambient temperature drawing after pickling
Core steps Piercing, rolling or extrusion, sizing, cooling, straightening Pickling, phosphating, drawing, intermediate annealing, final sizing
Reduction pattern Heavy reduction in a small number of passes Moderate reduction per pass with repeated anneals
Delivery condition As rolled, normalised or quenched and tempered As drawn, annealed or stress relieved

Dimensional Accuracy, Surface Finish and Mechanical Properties

Cold working tightens the dimensional class. Because the final forming step is a cold pass through a precision die, cold drawn tube reaches closer outside diameter and wall thickness tolerances, better concentricity, lower ovality and a smoother scale free surface. Hot rolled pipe keeps a mill scale layer and works inside the wider tolerance classes of the hot finished product standards.

The two routes also differ in strength. Cold drawing strain hardens the steel: tensile strength, yield strength and hardness rise while elongation and impact toughness fall. When the finished item has to meet a defined property range, the tube is ordered in the annealed or normalised condition and the mechanical values are verified on samples taken from the delivered lot in accordance with the ordering standard.

How to Choose Between Cold Drawn and Hot Rolled Pipe

Hydraulic and pneumatic cylinders, shock absorbers and precision mechanical parts: cold drawn tube to GB/T 3639 or EN 10305-1 for bore accuracy and surface quality.

Boiler and heat exchanger tubes: cold drawn tube to ASTM A179 or ASTM A192, or hot rolled tube to GB/T 3087 for lower pressure service.

Line pipe, structural tubing and general fluid conveyance: hot rolled seamless pipe to GB/T 8163, ASTM A106 or API 5L, where large diameters and heavy walls are required at lower cost.

Small diameter, thin wall and long length requirements: cold drawing, because the process reaches sizes that hot rolling cannot supply economically.

Inspection and Handling Points

Dimensional inspection covers outside diameter, wall thickness, ovality, length and straightness, with acceptance limits taken from the ordering standard. Additional tests commonly specified for seamless pipe include hydrostatic testing, eddy current or ultrasonic inspection, flattening, bending and expansion tests. Cold drawn tube should be stored on dry racks, because a pickled bright surface rusts faster than a scaled hot rolled surface. Mill records should always state the delivery condition, since the same nominal size can be produced by either route with different property outcomes.

FAQ

Q: Is cold drawn seamless pipe stronger than hot rolled pipe of the same grade?
In the as drawn condition yes, because cold work raises tensile and yield strength and hardness while reducing elongation. After annealing or normalising, the remaining difference is dimensional accuracy and surface quality rather than strength level.

Q: Which route gives better wall thickness tolerance?
Cold drawing. The cold finishing pass through a precision die produces closer wall and diameter tolerances and lower eccentricity than hot rolling, and the tighter classes are listed in the cold drawn product standards.

Q: Can a cold drawn pipe be used at high temperature?
Only in the annealed or normalised condition and within the temperature limits of the governing standard. The strain hardened structure recovers and softens on heating, so the as drawn condition is intended for ambient temperature mechanical service.

Q: Why is cold drawn pipe more expensive?
The route adds pickling, phosphating, drawing passes, inter pass annealing and straightening, and it produces shorter lengths with more handling. The added cost buys tighter tolerances, a smoother surface and smaller available sizes.

Q: Does the delivery condition need to be stated on the order?
Yes. The same grade can be supplied as rolled, normalised, annealed or as drawn, and the mechanical properties and subsequent forming behaviour differ. The delivery condition must appear in the contract and on the inspection certificate.

Send Inquiry