The Basis of Boiler Tube Pressure Design
A boiler tube is a pressure vessel with an unusually unfavourable geometry: thin wall, small diameter and high heat flux. Its thickness is determined by a code calculation rather than by mechanical convenience. For power boilers the governing rules are in ASME BPVC Section I. PG-27 establishes the required minimum thickness for tubes, pipes, drums and headers, and the formula differs between the tubular products used in the furnace and convection pass and the heavier shells, drums and headers.
The general form for shells, drums and headers is expressed as a function of the design pressure and the outside diameter divided by a denominator containing the allowable stress, a joint efficiency and a temperature coefficient, with an allowance added for corrosion, erosion and forming.
Inputs to the Thickness Calculation
Design pressure: the maximum pressure expected in service, taken from the boiler design data and not from the normal operating point.
Outside diameter: the nominal tube size, normally the dimension fixed by the required heat transfer surface and the circulation design.
Allowable stress S: taken from ASME BPVC Section II Part D at the design metal temperature, which may be far above the saturation temperature of the steam.
Joint efficiency E: applied to welded construction, with the value depending on the weld type and the extent of examination performed.
Temperature coefficient y: introduced for materials where the elevated temperature behaviour requires it, again taken from the code.
Corrosion and erosion allowance: an additional thickness agreed for the specific fuel, water chemistry and gas conditions.
Mill tolerance: the negative wall thickness deviation permitted by the tube specification, which must be accounted for so that the thinnest delivered wall still satisfies the calculation.
Material Selection and Elevated Temperature Behaviour
| Design metal temperature regime | Typical tube specification | Governing design consideration |
|---|---|---|
| Lower temperature boiler and economiser service | ASTM A192, EN 10216-2 P235GH | Tensile and yield strength at temperature |
| Higher strength boiler and superheater service | ASTM A210 Grade A-1 and C | Strength at moderate elevated temperature |
| Elevated temperature superheater and reheater | ASTM A213 T11, T22 | Creep and stress rupture properties |
| High temperature, high pressure service | ASTM A213 T91 | Creep strength and oxidation resistance |
| High temperature steam piping and headers | ASTM A335 P11, P22, P91 | Creep rupture data and weldability |
Above the temperature at which creep becomes significant, the allowable stress in ASME BPVC Section II Part D is based on stress to rupture and on creep rate rather than on tensile properties. Using tensile data in this regime is a common and serious design error, because it overstates the stress the tube can sustain for the design life.
Safety Factors and Tests
The design margins embedded in the code are intended to cover variability in material properties, fabrication and loading. Strength design is based on the tabulated allowable stress with its built-in margin on tensile strength, while the high-temperature regime relies on stress rupture criteria with an appropriate scatter band and a minimum average creep rate criterion. Where the geometry or the loading is outside the scope of the simple formula, the design is verified by finite element stress analysis, and the result is compared against the allowable limits of ASME BPVC Section VIII Division 2, which is widely used for this purpose.
Design Checks Beyond Thickness
Thickness is only the first check. The design must also demonstrate that the tube can tolerate thermal expansion without excessive stress, that supports and attachments do not introduce stress concentrations, that the tube-to-header or tube-to-drum joint is qualified for the pressure and temperature, and that the tube can be welded, bent and heat treated in production with the specified material. Piping connected to the boiler, such as the steam and feedwater lines in the same system, is designed to ASME B31.1, so the boiler designer and the piping designer must agree on the interface conditions of pressure, temperature and allowable load.
FAQ
Q: Which code gives the minimum wall thickness for boiler tubes?
ASME BPVC Section I, in PG-27, with the allowable stress values taken from ASME BPVC Section II Part D at the design metal temperature.
Q: Why is the design metal temperature higher than the steam temperature?
Because the tube wall runs hotter than the fluid it contains, by an amount that depends on heat flux, wall thickness, scale and internal cooling. The wall temperature, not the steam temperature, governs the allowable stress.
Q: What is the corrosion allowance used for?
It provides additional thickness to be consumed over the design life by fireside oxidation, water-side corrosion and erosion, so that the tube remains above the minimum calculated thickness when it is finally retired.
Q: Does a welded tube require a joint efficiency factor?
Yes. Where welded tubular products are permitted, the joint efficiency is applied in the thickness formula and depends on the weld type and on the extent of radiographic or ultrasonic examination performed.
Q: When is stress analysis required instead of the code formula?
When the geometry, the attachments or the thermal loading fall outside the assumptions of the simple formula, or when local stresses at supports, penetrations and header connections need to be quantified.





