What ASTM B165 Covers
ASTM B165 is the standard specification for nickel-copper alloy UNS N04400 seamless pipe and tube. The alloy is widely known under the trade-style name Monel 400, but procurement documents should always reference the UNS designation N04400 together with the standard number, because the specification governs the chemical limits, mechanical values, and tolerances, not the commercial name.
The base scope of B165 is cold-worked seamless pipe and tube. Hot-worked material can also be supplied, but in that case the mechanical properties and permissible tolerances are agreed between the manufacturer and the purchaser rather than taken from the standard tables. Inch-pound units are the governing units in the specification; metric values in parentheses are conversions for reference. For dimensional requirements the specification is used together with the tables established in ASTM B829 for seamless nickel and nickel-alloy pipe, and tension testing follows ASTM E8.
Material: UNS N04400
UNS N04400 is a nickel-copper solid-solution alloy with roughly two-thirds nickel and one-third copper. It is chosen for seawater service, chemical and hydrocarbon processing, and heat-exchanger duty where chloride resistance and moderate strength are required together with good fabricability. The chemical composition is fixed by the B165 table and, for the buyer, verified on the mill test certificate.
| Element | Limit (weight %) |
|---|---|
| Nickel (including cobalt) | 63.0 min |
| Copper | 28.0 - 34.0 |
| Iron | 2.5 max |
| Manganese | 2.0 max |
| Carbon | 0.30 max |
| Silicon | 0.50 max |
| Sulfur | 0.024 max |
For cold-worked pipe in the condition covered by the specification, the tensile requirements are on the order of 483 MPa (70 ksi) minimum tensile strength, 195 MPa (28 ksi) minimum yield strength, and 35% minimum elongation. These values are read from the B165 table for the specified size and condition and must be confirmed against the certificate for each delivered lot.
Size Range and Wall Series
B165 pipe is ordered by nominal pipe size (NPS) with a schedule wall designation, following the same logic used for stainless and nickel-alloy piping. The common range in the dimension tables runs from small-bore sizes around NPS 1/8 up to NPS 14, with wall series typically covering schedules 5S, 10S, 40S, and 80S; the S suffix denotes the stainless/nickel-alloy pipe series. Tube sizes below the pipe range are covered by the tube portion of the same standard with tighter dimensional limits. Because the standard is written in inches, dimensional data are also published in millimetres so that manufacturers, inspectors, and end users share one reference language.
How the Tolerances Are Structured
The tolerance tables in B165 follow the B829 format. The outside diameter tolerance is a function of the nominal size and of the condition of the pipe: cold-worked material carries a stated OD allowance that tightens as the nominal size decreases, and the wall thickness tolerance is expressed as a percentage of the nominal wall rather than a fixed millimetre value. This means a thick-wall schedule has a larger absolute allowance than a thin-wall schedule at the same nominal size. Length tolerances are stated as fixed allowances, and the specification also covers straightness and, where applicable, weight per unit length.
The practical consequence is that a buyer cannot verify compliance by measuring one pipe and comparing it with a general rule. Each dimension must be checked against the specific line in the B165 table for the ordered size, schedule, and condition. When a project specification adds a tighter requirement, that tighter value is written into the purchase order and takes precedence for acceptance.
Why Dimensional Tolerances Matter in Service
Tolerance control is not a paperwork exercise. Outside diameter accuracy determines how the pipe seats in pipe supports and how flanges and fittings engage during makeup. Wall thickness directly affects the pressure-containing cross-section: a wall below the minimum reduces the allowable working pressure calculated from the design code and is a safety issue, not just a quality issue. Consistent pipe ends matter for welding, because end-to-end mismatch under the torch produces misalignment, incomplete fusion, and weld defects that are expensive to find and repair. For these reasons, dimensional verification is part of the receiving inspection for any pressure or process system.
How to Verify Dimensions on Delivery
Verification uses calibrated instruments traceable to the quality system. Outside diameter is measured with an outside micrometer or a pi tape; wall thickness is checked with an ultrasonic thickness gauge at several points around the pipe end, which is non-destructive, or by cutting a ring and measuring with a micrometer, which is destructive and used only when permitted. Length is measured with a steel tape, and straightness is checked on a level surface. All readings are recorded and compared against the applicable B165 table lines; the mill certificate is the cross-reference for heat identity and condition.
Handling Out-of-Tolerance Material
If a measured dimension falls outside the permissible values, the pipe or the affected batch is rejected. The purchaser notifies the supplier promptly and provides the measurement record as evidence. Depending on the contract, the remedy is replacement with conforming material or, where the deviation is minor and agreed, a concession documented between both parties. Out-of-tolerance pipe must not be installed, and it is never acceptable in pressure-containing service even if the deviation looks small.
FAQ
1. Is ASTM B165 pipe seamless or welded?
B165 covers seamless pipe and tube only. The seamless product is produced from a solid billet by hot working or cold drawing, so there is no longitudinal weld to evaluate or inspect.
2. What is the alloy covered by B165?
UNS N04400, a nickel-copper alloy with 63% minimum nickel and 28-34% copper, commonly referenced as Monel 400 in the market.
3. Which wall schedules are available under B165?
The dimension tables commonly cover schedules 5S, 10S, 40S, and 80S in the pipe range up to NPS 14, with tube sizes carrying their own dimensional limits.
4. Is B165 material supplied in the annealed condition?
Cold-worked pipe in the specification is supplied in the condition established by the standard's table for the ordered size; the required condition is stated on the purchase order and confirmed on the mill certificate.
5. What is the difference between B165 pipe and B163 tube?
B165 covers N04400 seamless pipe and tube for general piping. B163 covers condenser and heat-exchanger tubes in several nickel alloys including N04400, with tube-specific dimensional and test requirements for exchanger service.
6. How is wall thickness tolerance expressed?
As a percentage of the nominal wall thickness for the ordered schedule, so the absolute allowance grows with the wall thickness rather than being a single fixed value.





