What Is ASTM A790?
ASTM A790 is the standard specification for seamless and welded ferritic-austenitic (duplex) stainless steel pipe for general corrosive service, with particular emphasis on resistance to chloride stress corrosion cracking. It fixes chemical composition, mechanical properties, heat treatment, hydrostatic testing, non-destructive testing and dimensional requirements for pipe.
Pipe under A790 is normally supplied in the solution-annealed condition: heated into the annealing range and quenched rapidly enough to prevent precipitation of intermetallic phases. That heat treatment is what produces the roughly balanced austenite-ferrite microstructure responsible for the grade family's combination of strength and corrosion resistance.
What Is ASTM A789?
ASTM A789 covers seamless and welded duplex stainless steel tubing for general service. In practice it is the specification called up for heat-exchanger, condenser and similar heat-transfer tubing, so it is associated with smaller diameters, tighter dimensional tolerances and cleaner surface finish than A790 pipe. The alloy grades overlap heavily between the two specifications.
Grade Coverage and Typical Composition
| UNS grade | Common name | Typical composition | Notes |
|---|---|---|---|
| S31803 / S32205 | 2205 duplex | About 22% Cr, 5.5% Ni, 3% Mo, 0.15% N | Most widely used duplex grade; good strength and corrosion balance |
| S32750 | Super duplex 2507 | About 25% Cr, 7% Ni, 4% Mo, 0.3% N | Very high strength and pitting resistance; PREN above 40 |
| S32760 | Super duplex with tungsten | About 25% Cr, 7% Ni, 3.5% Mo, 0.7% W, 0.3% N | Tungsten addition further improves corrosion resistance; PREN above 40 |
Within the duplex family the practical dividing line is the pitting resistance equivalent number (PREN), calculated as Cr + 3.3 x Mo + 16 x N. Standard duplex grades typically fall in the mid-30s and the super duplex grades sit above 40, which is why super duplex is selected where chlorides, warm seawater or sour service would attack a standard duplex grade.
Key Differences between A790 and A789
Product form: A790 is written around pipe for fluid transport lines and pipelines; A789 is written around tubing for heat exchangers and similar apparatus.
Size range: A789 is normally ordered in smaller outside diameters; A790 covers the larger diameters used for line pipe and process piping.
Fabrication practice: tubing is usually expanded into tube sheets and rolled or welded into headers, while pipe is joined by butt welding with matching duplex filler metal.
Inspection emphasis: tubing specifications focus on surface condition and dimensional precision; pipe specifications focus on weld integrity, pressure testing and non-destructive examination.
Because the grades are shared, a project can use the same duplex alloy in both forms - A789 tube for the exchanger bundle and A790 pipe for the connected line - provided the welding consumables and heat-treatment practice suit the thicker section.
Ordering and Fabrication Points
Duplex stainless steel is less forgiving than austenitic stainless steel in fabrication. Heat input must be controlled, interpass temperature limited, and copper-backed or ceramic backing preferred over carbon steel backing, which can contaminate the root. Filler metal should be nickel-enriched relative to the base metal to hold the ferrite-austenite balance in the weld. After welding, the joint should be cleaned of scale and iron contamination to preserve corrosion resistance.
On the order, state the UNS grade and the product form explicitly. A requirement written only as duplex stainless steel pipe leaves the grade, the heat-treatment condition and the inspection level open, and those are precisely the variables that determine whether the delivered material performs in chloride service.
FAQ
Q: What is ASTM A790?
A specification for seamless and welded ferritic-austenitic (duplex) stainless steel pipe for general corrosive service, written with emphasis on resistance to stress corrosion cracking.
Q: What is the difference between ASTM A790 and A789?
Both cover duplex stainless steel, but A789 is written for tubing used in heat exchangers and similar equipment, while A790 is written for pipe used in corrosive fluid transport. The grade list is largely shared.
Q: What material is UNS S32750?
It is a super duplex stainless steel, commonly called 2507, with roughly 25% chromium, 7% nickel, 4% molybdenum and 0.3% nitrogen, giving high strength and a PREN above 40.
Q: What material is UNS S31803?
It is a standard duplex stainless steel, commonly called 2205, with roughly 22% chromium, 5.5% nickel, 3% molybdenum and 0.15% nitrogen, offering a good balance of strength and corrosion resistance.
Q: What material is UNS S32760?
It is a super duplex grade with tungsten added to the composition, which raises corrosion resistance in aggressive chloride environments to a level comparable with other super duplex grades.
Q: Can A789 tubing and A790 pipe be welded to each other?
Yes, where the UNS grades are the same or compatible, using nickel-enriched duplex filler metal and a qualified welding procedure with controlled heat input.





