Nov 27, 2025 Leave a message

ASTM A672 Grade B60 Class 22 EFW Steel Pipe for High-Temperature Service

What ASTM A672 Grade B60 Class 22 Pipe Is

ASTM A672 is the standard specification for electric-fusion-welded (EFW) pipe made from pressure-vessel-quality plate with filler metal added, and written for high-temperature service at moderate temperatures. It is the counterpart of ASTM A671, which covers the same plate-based construction for atmospheric and lower-temperature service. Grade B60 Class 22 pipe is therefore a plate-based welded product: the cylinder is rolled from plate, the longitudinal seam is welded with filler metal, and the finished length is heat treated and examined to the class stated in the order.

The designation A672 Grade B60 Class 22 reads in three blocks. The letter pair identifies the pressure-vessel plate specification from which the cylinder is rolled, and the number that follows the letters keeps the grade numbering of that plate specification. The two-digit class number states the heat-treatment condition of the finished pipe together with the non-destructive examination and testing regime that applies to it. The class number must always be quoted together with the plate letters and the grade, because pipes of identical chemistry can be supplied in different heat-treatment conditions and with quite different levels of radiographic examination of the longitudinal seam.

Within the A672 system the letter block identifies the referenced pressure-vessel plate specification and the number that follows identifies the grade within that specification. For grade 60 of the referenced carbon steel plate specification, the mechanical requirements are a minimum specified yield strength of 220 MPa (32 ksi), a tensile strength range of 415 MPa to 550 MPa (60 ksi to 80 ksi) and a minimum elongation in 50 mm (2 in.) of 25 percent. The grade is therefore a moderate-strength, readily weldable carbon steel intended for elevated-temperature pressure service rather than for low-temperature toughness.

Manufacturing Route and Quality Control

Plate is purchased against the referenced pressure-vessel plate specification with chemical and mechanical certificates traced to each heat.

Plate edges are machined or planed, the shell is formed, and the longitudinal joint is prepared and tacked for welding.

The seam is welded with filler metal, normally by submerged arc welding with carbon steel electrode and flux combinations classified under AWS A5.17 / SFA-5.17, from one or both sides depending on the wall thickness.

Class 22 heat treatment is applied to the finished pipe, then the pipe is straightened, end-finished and cleaned.

Radiography of the longitudinal seam is carried out to the coverage required by the class, with magnetic particle or liquid penetrant examination of weld ends and repaired areas.

Each length is hydrostatically tested, marked with the full designation and released with a mill test report covering chemistry, tensile properties, heat treatment and examination results.

Specification and Dimensional Data

Item Reference or range
Product standard ASTM A672, electric-fusion-welded pipe for high-temperature service at moderate temperatures
Base material Pressure-vessel-quality carbon steel plate, identified by the letter block in the designation
Designation A672 Grade B60 Class 22
Minimum yield strength 220 MPa (32 ksi), per the referenced grade 60 plate requirements
Tensile strength 415 MPa to 550 MPa (60 ksi to 80 ksi)
Minimum elongation 25 percent in 50 mm (2 in.)
Outside diameter NPS 8 to NPS 48 as standard, outside diameters per ASME B36.10M
Wall thickness Selected against the order, up to 76 mm for heavy-wall service
Lengths 6 m to 12 m, or specific cut lengths
Seam type One or two longitudinal seams, welded with filler metal
Filler metal Carbon steel electrode and flux combinations to AWS A5.17 / SFA-5.17
Heat treatment As stated by the class number in the designation
Examination Radiography of the longitudinal seam and hydrostatic test as required by the class
End finish Plain, bevelled or as ordered

Service Applications

A672 Grade B60 Class 22 pipe serves in boiler and steam plant piping, feedwater and blowdown lines, process piping in refineries and chemical plants, heat exchanger and drum connections, and general elevated-temperature utility piping where a plate-based, heat-treated and radiographed pipe is required at moderate strength. Because the grade is a readily weldable carbon steel, the material is also common where field welding quality and repeatability matter more than the highest available strength level.

Ordering, Fabrication and Inspection Points

The order should state the product standard, the plate letter block and grade, the class number, nominal size and wall thickness, length and end finish, the design and operating temperatures, radiographic coverage, hydrostatic test pressure, heat-treatment condition, surface condition and coating, marking requirements and the contents of the mill test report.

Fabrication follows a welding procedure qualified to ASME BPVC Section IX. For elevated-temperature carbon steel service, control of heat input, preheat and interpass temperature, correct low-hydrogen consumables and, where the class or the thickness requires it, post-weld heat treatment all influence the properties and the residual stress state of the finished joint. Documentation should preserve traceability from the plate heat number through to the released pipe, because that chain is what demonstrates conformity when a third-party inspector reviews the order.

FAQ

Q: What is the difference between ASTM A671 and ASTM A672?
Both standards cover electric-fusion-welded pipe made from pressure-vessel plate with filler metal added and share the same letter, grade and class designation system. A672 is written for high-temperature service at moderate temperatures, while A671 is written for atmospheric and lower-temperature service.

Q: What does grade B60 mean in an A672 designation?
The letter block identifies the referenced pressure-vessel plate specification and the number that follows identifies the grade within it. For grade 60 of the referenced carbon steel plate specification, the minimum specified yield strength is 220 MPa (32 ksi) and the tensile range is 415 MPa to 550 MPa.

Q: What does class 22 control?
The class number states the heat-treatment condition of the finished pipe together with the non-destructive examination and testing regime that applies to it. Class 22 pipe is heat treated after welding and examined in accordance with the class, and both are recorded in the documentation released with the order.

Q: Is this pipe seamless?
No. It is electric-fusion-welded pipe, formed from plate and welded with filler metal along one or two longitudinal seams. The class number governs the heat treatment and the examination of that seam and of the pipe body.

Q: Which sizes and lengths are practical?
Plate-based EFW pipe is normally produced from NPS 8 to NPS 48 with outside diameters per ASME B36.10M, in wall thicknesses well beyond the range of standard line pipe, and in lengths of approximately 6 m to 12 m or to specific cut lengths.

Q: What should the mill test report contain?
The plate specification and grade, the class number, the heat and pipe numbers, the chemical analysis, the tensile results, the heat-treatment record, the radiographic examination coverage and results, and the hydrostatic test record, so that each length can be traced back to the plate from which it was made.

Send Inquiry