Dec 20, 2025 Leave a message

ASTM A671 CD80 Class 43 Steel Pipe: Normalized and Tempered A537 Class 2 EFW Pipe

Overview of ASTM A671 CD80 Class 43 Pipe

ASTM A671/A671M is the specification for electric-fusion-welded steel pipe made from pressure-vessel-quality plate, intended for high-pressure service at atmospheric and lower temperatures. The pipe is formed from plate and welded with a double-sided submerged arc weld, then heat treated and examined according to the class. It is produced in large diameters, normally 16 in, about 406 mm, and larger.

The designation CD80 Class 43 has two independent parts. CD80 names the plate material and its strength level: the pipe is made from A537/A537M Class 2 plate, a manganese-silicon steel, quenched and tempered. Class 43 names the heat treatment and examination requirements applied to the finished pipe. Each part is explained below.

What the Grade Means

In the A671 designation the two-letter prefix identifies the pressure-vessel plate specification from which the pipe is made, and the number states the minimum tensile strength in ksi. The grade CD80 therefore means pipe made from A537/A537M Class 2, with a minimum tensile strength of 80 ksi, about 550 MPa.

Grade Plate specification Steel type Minimum tensile strength
CD80 A537/A537M Class 2 manganese-silicon steel, quenched and tempered 80 ksi, about 550 MPa

CD80 is made from A537 Class 2 plate, a manganese-silicon carbon steel supplied in the quenched and tempered condition. The plate tensile range is 80 to 100 ksi, combining high strength with dependable low-temperature toughness.

In terms of strength, The minimum yield strength of the plate is 60 ksi, about 415 MPa, for thicknesses up to 2.5 in..

How the A671 Class System Works

The class is a two-digit code. The first digit selects the heat-treatment family applied to the pipe after welding.

Class family Heat treatment applied to the pipe
10 to 13 None; delivered as welded
20 to 23 Stress relieved after welding
30 to 33 Normalized
40 to 43 Normalized and tempered
50 to 53 Quenched and tempered
70 to 73 Quenched and precipitation heat treated

The second digit selects the examination level.

Last digit Radiography of the weld Pressure test
0 Not required Not required
1 Full-length radiography of each weld per ASME VIII UW-51 Not required
2 Full-length radiography of each weld per ASME VIII UW-51 Required per A530/A530M
3 Not required Required per A530/A530M

What Class 43 Means for This Pipe

Class 43 has two digits. The first digit 4 selects the heat-treatment family, which means the pipe is normalized and then tempered after welding. The second digit 3 selects the examination level, which means no full-length radiography is required by the class, but a hydrostatic pressure test is required in accordance with A530/A530M.

Taken together, Class 43 pipe is the pipe is normalized and then tempered after welding, and no full-length radiography is required by the class, but a hydrostatic pressure test is required in accordance with A530/A530M. These requirements are fixed at the time of ordering, recorded on the order documents and confirmed on the mill test certificate.

A537 Class 2 is itself a quenched and tempered plate, so pipe classes in the 40 to 53 range are a reasonable match; the heat treatment of the finished pipe should be confirmed on the order.

Typical Applications

CD80 pipe is used for ammonia storage spheres, LPG and propylene vessels, penstocks and heavy-wall pressure piping where the quenched and tempered A537 Class 2 plate family provides high design stress at lower temperatures.

Manufacturing, Testing and Documentation

A671 pipe starts as pressure-vessel-quality plate supplied under the applicable plate standard. The plate is formed into a cylinder and the longitudinal seam is welded by the submerged arc process from both the inside and the outside, producing a full-penetration weld. After welding, the pipe receives the heat treatment of the selected class and then the examination and tests required by the class and by A671/A671M.

Testing normally includes chemical analysis of the heat, tensile testing, and the radiography and hydrostatic pressure tests required by the class. Charpy V-notch impact testing is performed when the design code or the purchase order requires it, and the plate may be ultrasonically examined under A435 or a supplementary requirement. Every pipe is traceable to its plate heat number, and the mill test certificate records the chemical analysis, mechanical test results, heat treatment details and examination results.

The available outside diameters, wall thicknesses and lengths depend on the plate widths and the forming and welding capability of the producing mill, so the required OD, wall, length and end finish should be confirmed with the supplier before ordering.

FAQ

Q1. What does the grade CD80 mean in the A671 designation?

The two-letter prefix identifies the plate specification, and the number states the minimum tensile strength in ksi. CD80 means pipe made from A537/A537M Class 2 plate, a manganese-silicon steel, quenched and tempered, with a minimum tensile strength of 80 ksi, about 550 MPa.

Q2. What does Class 43 mean?

Class 43 is read in two digits: the first digit selects the heat-treatment family, the pipe is normalized and then tempered after welding, and the second digit selects the examination level, which means no full-length radiography is required by the class, but a hydrostatic pressure test is required in accordance with A530/A530M.

Q3. What is the minimum tensile strength of CD80 pipe?

80 ksi, about 550 MPa. The number in the grade name states this value directly; it is a tensile value, not a yield value. The minimum yield strength of the plate is 60 ksi, about 415 MPa, for thicknesses up to 2.5 in.

Q4. Does Class 43 define a service temperature?

No. A class defines heat treatment and examination only, never a service temperature. The safe operating temperature is set by the plate material, the impact test requirements and the governing design code; for the CD80 grade, the steel family and its qualified toughness determine the low-temperature limit.

Q5. What tests are performed on A671 pipe?

Every heat is verified by chemical analysis and tensile testing. The class determines whether full-length radiography of the longitudinal weld and a hydrostatic pressure test are required. Charpy impact testing, ultrasonic examination of the plate and other supplementary tests are added when the design code or the purchase order specifies them, and all results are reported on the mill test certificate.

Q6. How is A671 pipe manufactured and what sizes are available?

A671 pipe is formed from pressure-vessel-quality plate and welded with a double-sided submerged arc weld, then heat treated and examined per the class. It is produced in outside diameters of 16 in, about 406 mm, and larger, with wall thicknesses selected for the design pressure and lengths typically supplied in single or double random. Exact availability depends on the producing mill and must be confirmed before ordering.

Send Inquiry