Nov 30, 2025 Leave a message

ASTM A671 CC60 Class 40 EFW Steel Pipe for Cryogenic and Cold Service

What Is ASTM A671 CC60 Class 40 Pipe?

ASTM A671 CC60 Class 40 pipe is an electric-fusion-welded (EFW) steel pipe made from pressure-vessel-quality carbon steel plate, with filler metal added at the longitudinal seam. It is governed by ASTM A671/A671M, the specification for EFW pipe in atmospheric and lower-temperature service, and it is ordered when a cold-duty line needs large diameter or heavy wall that is difficult to source as seamless pipe.

The designation reads in three parts. CC is the grade letter group that fixes the heat-treatment and impact-testing route, 60 is the minimum tensile strength level in ksi, and Class 40 is the plate and test condition selected from the ordering table. Because the grade level is 60 ksi (414 MPa), the pipe offers useful ductility for cold service without resorting to alloy plate.

Toughness, not strength, is the decisive property in cryogenic and cold-side service. The specification therefore works with Charpy V-notch impact testing at a temperature agreed between purchaser and mill, and the order must state that temperature explicitly for the requirement to be enforceable.

Grade, Class and Test Requirements

Item Requirement
Specification ASTM A671/A671M, EFW pipe for atmospheric and lower temperatures
Grade CC60, grade letter group CC with a 60 ksi (414 MPa) minimum tensile level
Class Class 40, plate material and test condition from the A671 ordering table
Seam Longitudinal seam welded with filler metal, single or double welded
Toughness Charpy V-notch impact test at the ordered test temperature
Weld examination Radiographic or ultrasonic examination along the full seam
Pressure test Hydrostatic test per the specification unless otherwise ordered
Heat treatment As-welded, stress-relieved or normalized as ordered
Ends Plain, beveled or prepared to the drawing and purchase order

Hydrostatic testing and weld examination are the routine release tests, while the impact test carries the low-temperature qualification. Tensile and chemical results from the plate heat and from the finished pipe complete the test report, which should accompany every shipment of cold-service pipe.

Forming, Welding and Heat Treatment

Plate is cut to length, formed and rolled to the ordered diameter, and the longitudinal edges are prepared before seam welding with filler metal. The weld is made under a qualified procedure, and dimensional checks on diameter, wall, out-of-roundness and end preparation are carried out before examination.

Radiographic or ultrasonic examination of the full seam provides the record of weld soundness; repairs are allowed within specification limits and must be re-examined. Where the order calls for it, heat treatment is carried out in the as-welded, stress-relieved or normalized condition, and the treatment is stated on the test report so that the delivered condition can be verified against the design requirement.

Cryogenic and Cold-Service Applications

CC60 Class 40 pipe is used for cold-side process piping such as liquefied gas transfer systems, gas treatment and dehydration units, refrigeration circuits and low-temperature storage connections. Its 60 ksi plate level is well matched to equipment and header duties where ductility and weldability are valued over the highest available tensile level.

The large-diameter welded format reduces the number of field girth welds in long runs, which matters where welding at low ambient temperature is restricted by procedure limits. Pipe may be supplied in stress-relieved condition for such jobs so that field welding and inspection procedures are easier to qualify.

Ordering, Inspection and Handling Notes

Specify specification, grade, class, size, wall, length and impact test temperature in the same enquiry.

Decide the heat-treatment condition before the plate is ordered, not after welding.

Require radiographic or ultrasonic seam examination and the corresponding test reports.

Check that impact results relate to the pipe as delivered, including any heat treatment applied.

Store and transport with ends protected, keeping the weld seam off the support line.

FAQ

Q: What does CC60 mean in ASTM A671?
CC is the grade letter group that fixes the heat-treatment and impact-testing route, and 60 is the minimum tensile strength level in ksi, giving a 60 ksi (414 MPa) minimum tensile product.

Q: Is this pipe suitable for cryogenic service?
It is produced for atmospheric and lower-temperature duty and can be ordered with Charpy V-notch impact testing at the design metal temperature, which is what cryogenic and cold-side service requires.

Q: How is the class number used?
The class entry selects the plate material and test condition from the ordering table of the specification and is always quoted together with the grade.

Q: What tests come with the pipe?
Chemical and tensile results from the plate, weld examination records for the seam, hydrostatic test results and, where ordered, Charpy V-notch impact results.

Q: Can heat treatment be stress relieving?
Yes. The specification allows as-welded, stress-relieved or normalized supply as ordered, and the treatment applied is recorded on the test report.

Q: Why choose welded rather than seamless pipe?
Large diameter and heavy wall combinations, long continuous runs with few girth welds and full weld examination records make the EFW route attractive for station and header piping.

Send Inquiry