Jul 31, 2025 Leave a message

ASTM A519 4815 Steel Pipe


1. Material Definition and Core Properties
Q: What is ASTM A519 4815 steel pipe?
A:
4815 steel pipe is a low-carbon nickel-chromium-molybdenum alloy steel seamless pipe (UNS G48150) specified in the ASTM A519 standard. Its core composition is: 0.13%-0.18% carbon, 3.25%-3.75% nickel, 1.65%-2.00% chromium, and 0.20%-0.30% molybdenum. This material, through a high nickel-chromium-molybdenum composite reinforcement design, achieves a groundbreaking combination of ultra-high cryogenic toughness (impact energy ≥ 40J at -196°C) and deep hardenability (oil quenching critical diameter 150mm). After special heat treatment, the reversed austenite content can reach 15%-20%. Its hydrogen embrittlement resistance (NACE TM0284 cracking rate ≤ 3%) surpasses similar materials, making it particularly suitable for ultra-low temperature and high-pressure hydrogen environments.

2. Mechanical Properties and Technical Parameters
Q: What are the performance indicators of 4815 steel pipe?
A:
In the quenched and tempered state (850°C oil quenching + 600°C tempering):

Strength: Tensile strength 950-1150 MPa, yield strength 800-950 MPa
Toughness: Elongation ≥ 16%, reduction of area ≥ 55%, -196°C impact energy ≥ 40J
Special Properties: Fracture toughness (KIC @ -196°C) ≥ 75 MPa·m¹/², high-pressure hydrogen environment slow strain rate test (SSRT) fracture time ≥ 200h
After cryogenic treatment (-196°C x 24h), the retained austenite content can be stably controlled to ≤5%.
3. Typical Applications
Q: What are the main applications of 4815 steel pipe?
A:

Ultra-cryogenic equipment: LNG tank liner support structures, liquid hydrogen pipelines (-253°C environment)

Energy extreme environments: fusion reactor superconducting magnet support rings, supercritical water-cooled reactor pressure vessels

Aerospace: liquid oxygen/liquid hydrogen rocket engine turbine pump casings (must comply with AMS 6532 standard)

Military strategy: cold-resistant load-bearing components for polar icebreakers, cryogenic sealed cabins for deep space probes

4. Key points for heat treatment and processing

Q: How to optimize the heat treatment and processing of 4815 steel pipe? A:
The "ultrafine grain pretreatment + reverse austenite control" process must be used:

Cyclic austenitization (950°C × 1h → 700°C × 2h, repeated three times) to achieve ASTM grade 12-14 ultrafine grains.

Warm rolling in the two-phase region (750°C) to 30%-40% deformation followed by direct quenching.

Multi-stage aging (475°C × 8h → 600°C × 4h) to stabilize the nano-sized Ni₃Ti precipitation phase.

Processing restrictions:

Welding requires ERNiCrMo-12 wire and preheating to 200-250°C.

Turning is limited to diamond-coated tools (cutting speed ≤ 25 m/min).

Hot forging temperatures must be strictly controlled within a narrow window of 1100-900°C.

5. Comparison with Similar Materials

Q: What is the difference between 4815 and 9% Ni steel and Invar 36? A:

vs. 9% Ni steel: 4815 has a lower nickel content (3.25%-3.75% vs. 9%), resulting in a 40% lower cost and better weldability, but slightly lower impact energy at -196°C.

vs. Invar 36: 4815 is 3-4 times stronger, but has a 50% higher coefficient of thermal expansion (CTE) than Invar 36.

Non-Substitution Principle:
▶ It is strictly prohibited to substitute Haynes 230 for use in oxidizing environments above 1600°C.
▶ It is prohibited to substitute Ti-6Al-4V for aerospace structural parts where weight reduction is a priority.

info-270-186

Send Inquiry