Jul 31, 2025 Leave a message

ASTM A519 Grade 1330 Seamless High-Manganese Mechanical Tubing

What ASTM A519 Grade 1330 Tubing Is

ASTM A519 grade 1330 is a medium-carbon, high-manganese mechanical tubing grade registered with the UNS number G13300. Carbon is held in the 0.28–0.33% range and manganese is raised to 1.60–1.90%, roughly three times the level found in plain carbon grades. Manganese is the least expensive element that materially improves hardenability in steel, so grade 1330 offers a useful through-hardening response on medium sections without the cost of chromium, nickel or molybdenum additions.

The combination of moderate carbon and high manganese produces a steel that machines well in the annealed or normalized condition and then responds predictably to quenching and tempering. It is widely used in machinery where a shaft or sleeve must carry a moderate load after heat treatment and where the economics of a low-alloy grade matter.

Chemical Composition and Hardenability

Element ASTM A519 grade 1330
Carbon 0.28–0.33%
Manganese 1.60–1.90%
Phosphorus 0.040% max
Sulphur 0.050% max

ASTM A519 tabulates the minimum tensile strength, yield strength and elongation for each grade and delivery condition, so the values quoted for a 1330 tube depend on whether it is supplied hot finished, cold drawn or heat treated. It is common practice to order the tubing annealed for machining and then to harden and temper the finished part, which lets the final heat treatment set the properties rather than the tube mill.

The high manganese content should be taken into account when the steel is cut or welded. The grade is tougher and work hardens more readily than a plain carbon steel of similar carbon level, so cutting speeds and feeds must be set accordingly, and sections that will be welded benefit from a controlled preheat and a slow cool.

Sizes, Tolerances and Purchasing Notes

Grade 1330 is produced as seamless tubing across a wide range of outside diameters and wall thicknesses, and the dimensional tolerances, straightness and length rules come from the ASTM A519 tables. Orders for heat-treatable parts should state the delivery condition, the required hardness or strength range after heat treatment and the examination requirements. Where a hardened part will be machined after treatment, the tube should be ordered with sufficient stock to allow for distortion during quenching.

Typical Applications

Drive shafts, axle shafts and stub shafts in off-highway and agricultural machinery

Sleeves, bushings and collars for moderate-load bearing arrangements

Gear blanks, sprocket hubs and coupling bodies produced from tube stock

Pins, tie rods and linkage parts in construction and material handling equipment

Mold ejector components and machine tool accessories in the quenched and tempered condition

Heat Treatment and Processing Guidance

The usual sequence is to normalize the tube before machining, then austenitize, quench in oil and temper to the required strength and toughness. Normalizing refines the grain structure and gives a uniform, more machinable condition. Oil quenching is preferred over water quenching, because the high manganese content provides sufficient hardenability while the gentler quench limits the risk of cracking and distortion. Tempering temperature is selected within the usual range for medium-carbon steels, with lower temperatures giving higher strength and higher temperatures giving better toughness.

For machining, coated carbide tooling is used at moderate cutting speeds with a positive rake geometry, and a heavier feed is preferable to a light rubbing cut because the material work hardens. Weldability is acceptable but not equal to that of low-carbon grades: a preheat in the region of 200–300 °C together with a controlled slow cool after welding reduces the risk of a hard, crack-sensitive heat affected zone.

FAQ

Q: What makes grade 1330 different from a plain carbon grade such as 1035?
It is the manganese level. Manganese at 1.60–1.90% substantially improves hardenability, so a 1330 component can be through-hardened on sections where a plain carbon steel of similar carbon content would harden only at the surface.

Q: How is ASTM A519 1330 tubing normally heat treated?
Typically by normalizing before machining and then austenitizing, oil quenching and tempering after machining. The tempering temperature is chosen to give the strength and impact toughness required by the finished part.

Q: Is water quenching suitable for grade 1330?
Oil quenching is the normal practice. The manganese content provides enough hardenability for medium sections, and the slower oil quench reduces the risk of quench cracking and distortion compared with a water quench.

Q: Can 1330 tubing be welded?
It can be welded with suitable procedures, but it is not a low-carbon welding grade. A preheat of roughly 200–300 °C and a controlled slow cool after welding are recommended to avoid a hard heat affected zone.

Q: What mechanical properties does ASTM A519 require for grade 1330?
The specification lists minimum tensile strength, yield strength and elongation for each grade and each delivery condition in its property tables. Because the values differ by condition, the purchase order must state whether the tube is hot finished, cold drawn or heat treated.

Q: Which sizes are available in grade 1330 tubing?
Seamless tubing is produced across a wide range of outside diameters and wall thicknesses, with dimensional tolerances following the ASTM A519 tables. Non-standard sizes can be discussed against available tooling and order quantity.

Send Inquiry