

ASTM A500 Structural Steel Pipe Technical Specification
Overview
ASTM A500 is the standard specification for cold-formed welded and seamless carbon steel structural tubing in round, square, and rectangular shapes. It is specifically designed for structural applications rather than pressure service, making it the primary standard for columns, beams, trusses, and other load-bearing construction elements.
Grade Classifications & Shapes
| Grade | Shapes Available | Yield Strength (min) | Typical Applications |
|---|---|---|---|
| Grade A | Round, Square, Rectangular | 39,000 psi (269 MPa) | Light to moderate structural loads |
| Grade B | Round, Square, Rectangular | 46,000 psi (317 MPa) | General construction, moderate loads |
| Grade C | Round, Square, Rectangular | 50,000 psi (345 MPa) | Heavy structural, high-rise construction |
| Grade D | Square & Rectangular only | 36,000 psi (248 MPa) | Architectural, lighter structural |
Note: Grade D has lower strength but better surface requirements for exposed architectural applications.
Mechanical Properties
Tensile Requirements:
| Grade | Tensile Strength (min) | Yield Strength (min) | Elongation in 2" (min) |
|---|---|---|---|
| A | 45,000 psi (310 MPa) | 39,000 psi (269 MPa) | 25% |
| B | 58,000 psi (400 MPa) | 46,000 psi (317 MPa) | 23% |
| C | 62,000 psi (427 MPa) | 50,000 psi (345 MPa) | 21% |
| D | 58,000 psi (400 MPa) | 36,000 psi (248 MPa) | 23% |
Additional Requirements:
For shapes ≤ 3" perimeter: Elongation measured in 1" gauge length
Transverse strip tests required for material ≤ 0.180" thick
Full-section tests for material > 0.180" thick
Chemical Composition (Maximum % unless range specified)
| Element | Grade A | Grade B | Grade C | Grade D |
|---|---|---|---|---|
| Carbon | 0.26 | 0.26 | 0.23 | 0.20 |
| Manganese | 1.35 | 1.35 | 1.35 | 1.35 |
| Phosphorus | 0.035 | 0.035 | 0.035 | 0.035 |
| Sulfur | 0.035 | 0.035 | 0.035 | 0.035 |
| Copper (min) | 0.20* | 0.20* | 0.20* | 0.20* |
When specified for enhanced atmospheric corrosion resistance. Copper minimum applies when corrosion resistance is required.
Manufacturing Processes
ERW Production for Structural Tubing:
Coil Preparation - Hot-rolled or cold-rolled steel, often with improved surface quality
Forming - Cold-forming through progressive roll stands
High-Frequency Welding - Typically 200-450 kHz for structural integrity
Weld Treatment - Flash removal, sometimes heat treatment for stress relief
Sizing - Final dimensional calibration
Cutting - Saw cutting to precise lengths
Testing - Mechanical and dimensional verification
Special Considerations for Structural Shapes:
Corner Radii - Controlled for consistent structural properties
Flatness - Critical for square and rectangular sections
Straightness - Tight tolerances for construction applications
Standard Sizes & Dimensions
Round Structural Pipe (Common Sizes):
| Outside Diameter | Wall Thickness Range | Common Applications |
|---|---|---|
| 0.840" - 2.375" | 0.083" - 0.154" | Handrails, light structural |
| 2.875" - 6.625" | 0.125" - 0.280" | Columns, medium structural |
| 8.625" - 16.000" | 0.188" - 0.500"+ | Heavy columns, piling |
Square & Rectangular HSS (Hollow Structural Sections):
| Size Range | Wall Thickness | Aspect Ratios |
|---|---|---|
| 1"×1" to 20"×20" | 0.065" to 1.000"+ | Square: 1:1 |
| 2"×1" to 20"×12" | 0.065" to 0.750"+ | Rectangular: Up to 5:1 |
Note: HSS refers to Hollow Structural Sections, the modern terminology for structural tubing.
Dimensional Tolerances (Per ASTM A500)
| Parameter | Tolerance for Round | Tolerance for Square/Rectangular |
|---|---|---|
| Outside Dimensions | ±0.5% of OD or ±0.010" (greater) | ±0.010" per inch or ±0.5% (greater) |
| Wall Thickness | ±10% of nominal | ±10% of nominal |
| Corner Radius | - | Maximum 2.0× wall thickness |
| Squareness | - | ±1° maximum deviation |
| Straightness | 0.10% of length | 0.10% of length |
| Twist | - | 1° per 3 feet maximum |
| Length | +1/4", -0" for cut lengths | +1/4", -0" for cut lengths |
Testing Requirements
| Test | Requirement | Frequency | Purpose |
|---|---|---|---|
| Tensile Test | Per ASTM A370 | 2 per heat, per wall thickness | Verify mechanical properties |
| Flattening Test | Flatten to 2/3 original height without cracking | 2 per lot | Ductility verification |
| Reverse Flattening Test (ERW only) | Opens weld for visual inspection | 1 per lot | Weld quality assessment |
| Hardness Test | Optional, per agreement | As specified | Additional quality check |
| Bend Test | For material ≤ 0.180" thick | 2 per lot | Formability assessment |
| Dimensional Inspection | All critical dimensions | Sample basis | Ensure fit for construction |
Note: Unlike pressure pipe, ASTM A500 does NOT require hydrostatic testing.
Surface Conditions & Finishes
| Condition | Description | Structural Application |
|---|---|---|
| As-Welded | Mill scale present, weld visible | Interior structures, to be painted |
| Pickled & Oiled | Clean, bright finish with oil film | Exposed architectural, immediate painting |
| Galvanized | Hot-dip zinc coated (per ASTM A123) | Corrosion protection for exposed structures |
| Abrasive Blasted | Clean, anchor pattern surface | For coating adhesion, exposed structures |
| Pre-Primed | Shop-applied primer | Fast-track construction |
Primary Structural Applications
Building Construction:
Columns & Posts - Vertical load-bearing members
Beams & Girders - Horizontal load-carrying members
Truss Members - Diagonal bracing, chords
Purlin & Girt Systems - Roof and wall support
Handrails & Guardrails - Safety systems
Infrastructure:
Bridge Components - Arches, bracing, rail supports
Transmission Towers - Electrical utility structures
Sign Supports - Highway signage structures
Light Poles - Street and area lighting
Industrial & Commercial:
Rack Systems - Storage rack uprights and beams
Equipment Supports - Machinery foundations, platforms
Agricultural Structures - Greenhouses, equipment shelters
Recreational - Playground equipment, sports facilities
Design Considerations & Advantages
Structural Advantages:
High Strength-to-Weight Ratio - Efficient material use
Torsional Resistance - Excellent for columns and torsional members
Uniform Properties - Consistent in all directions
Aesthetic Appeal - Clean lines for architectural exposure
Ease of Connection - Simple bolted or welded connections
Internal Protection - Enclosed section protects from corrosion
Design References:
AISC Steel Construction Manual - Primary design reference
AISI North American Specification - Cold-formed steel design
AWS D1.1 - Structural welding code
Connection Methods
| Method | Typical Use | Considerations |
|---|---|---|
| Direct Welding | Moment connections, rigid frames | Preheat for thicker sections, weld access |
| Gusset Plate Connections | Trusses, bracing | Plate thickness matching, weld patterns |
| Through-Bolting | Simple connections, field assembly | Hole tolerance, bolt spacing |
| End Plates | Column bases, moment connections | Flatness, weld distortion control |
| Slip-Critical Bolting | Seismic, fatigue applications | Surface preparation, bolt tensioning |
Comparison with Other Structural Standards
| Parameter | ASTM A500 | ASTM A53 | ASTM A1085 |
|---|---|---|---|
| Primary Use | Structural | Pressure/Mechanical | Structural (improved) |
| Tolerances | Structural fit-up | Pipe system fit-up | Tighter than A500 |
| Corner Radius | Controlled | Not applicable | More restrictive |
| Testing Focus | Mechanical properties | Pressure integrity | Enhanced properties |
| Weld Requirements | Structural integrity | Fluid containment | Highest integrity |
| Common Shapes | Round, Square, Rectangular | Round only | Round, Square, Rectangular |
Fabrication Guidelines
Cutting Methods:
Saw Cutting - Most common, clean square cuts
Plasma Cutting - Fast, for complex shapes
Abrasive Cutting - For onsite modifications
Laser Cutting - Precision, high-volume production
Bending & Forming:
Cold Bending - Up to yield point without cracking
Minimum Bend Radius - Typically 3× OD for round, 2.5× for HSS
Springback Allowance - Consider in tooling design
Heat-Assisted Bending - For tight radii or thick walls
Welding Considerations:
Filler Metal Selection - Typically E70XX for matching strength
Weld Access - Limited for closed sections
Heat Input Control - Prevent distortion in thin walls
Preheat - Recommended for thickness > 0.75"
Quality Control & Inspection
Inspection Points:
Dimensional Verification - OD, wall, straightness, squareness
Surface Quality - Free of excessive scale, pits, defects
Weld Integrity - Continuous, uniform weld seam
End Condition - Square, burr-free ends
Coating/Finish - Per specification requirements
Certification Requirements:
Mill Test Certificate - Required with shipment
Heat Number Traceability - Essential for critical structures
Third-Party Inspection - Often required for large projects
Load Tables & Design Aids
Common Design Values (Example - Round HSS):
| Size (OD × Wall) | Grade B Area (in²) | I (in⁴) | S (in³) | r (in) |
|---|---|---|---|---|
| 6.625" × 0.250" | 5.01 | 30.7 | 9.26 | 2.48 |
| 8.625" × 0.322" | 8.40 | 75.6 | 17.5 | 3.00 |
| 10.75" × 0.365" | 11.9 | 146 | 27.2 | 3.50 |
Complete tables available in AISC Manual and manufacturer catalogs.
Sustainability & Environmental Aspects
Recycled Content - Typically contains 25-35% recycled steel
Recyclability - 100% recyclable at end of life
Coating Systems - Low-VOC paints and powder coatings available
Fabrication Efficiency - Minimal waste compared to open sections
Life Cycle - Long service life with proper maintenance
Industry Standards & Code Compliance
Key References:
AISC 360 - Specification for Structural Steel Buildings
IBC - International Building Code
AASHTO - Bridge design specifications
ASCE 7 - Minimum design loads
AWS D1.1/D1.8 - Structural welding codes
Certification Programs:
AISC Certification - For fabricators and erectors
ICBO Evaluation Service - Product evaluation reports
UL Classification - Fire resistance ratings
Failure Modes & Prevention
| Failure Mode | Causes | Prevention |
|---|---|---|
| Local Buckling | Thin walls, high compression | Wall slenderness limits |
| Overall Buckling | Excessive unbraced length | Proper bracing, slenderness control |
| Connection Failure | Poor detailing, overloading | Connection design, quality control |
| Fatigue | Cyclic loading, stress concentrations | Detail design, smooth transitions |
| Corrosion | Environmental exposure | Protective coatings, maintenance |
Ordering Information
Complete Specification Should Include:
Standard & Grade - ASTM A500 Grade B
Shape - Round, Square, or Rectangular HSS
Dimensions - Outside dimensions × wall thickness × length
Tolerances - Standard or special
Finish - As-welded, pickled, galvanized, etc.
End Treatment - Saw cut, milled, coped
Certification - Mill test certificate requirements
Marking - Required identification
Packaging - Bundle size, protection requirements
Special Requirements (When Needed):
Enhanced Tolerances - For precision applications
Special Straightness - For long spans or aesthetic requirements
Surface Preparation - For specific coating systems
Testing Witness - Third-party inspection requirements
Special Marking - Color coding, lot identification
Storage & Handling
Best Practices:
Support - Adequate blocking to prevent bending
Separation - Different sizes/grades to prevent mixing
Protection - From dirt, moisture, and damage
Identification - Clear marking for easy retrieval
First-In-First-Out - Proper rotation of inventory
Lifting & Moving:
Spreaders - Use to prevent bending during lifting
Chokers - Proper slinging techniques
Weight Limits - Consider bundle weights for equipment capacity
Cost Considerations
Factors Affecting Price:
Grade - Grade C typically 5-10% premium over Grade B
Size Availability - Common sizes most economical
Quantity - Volume discounts available
Finish - Galvanized adds 30-50% to base cost
Tolerances - Special tolerances increase cost
Testing - Additional testing adds to cost
Industry Trends & Developments
Current Trends:
Higher Strength Grades - Increasing use of Grade C for efficiency
Sustainability Focus - Environmental product declarations (EPDs)
Digital Fabrication - BIM integration, automated fabrication
Coating Innovations - Longer-life, lower-maintenance systems
Hybrid Systems - Combining HSS with other materials
Future Directions:
Advanced High-Strength Steels - For even more efficient sections
Smart Structures - Embedded sensors for monitoring
Additive Manufacturing - Custom nodes and connections
Circular Economy - Design for disassembly and reuse
Summary
ASTM A500 structural steel pipe and HSS provide versatile, efficient structural elements for a wide range of construction applications. Their combination of strength, aesthetics, and fabrication flexibility makes them a preferred choice for modern steel construction. Proper selection based on structural requirements, attention to connection design, and adherence to fabrication best practices ensure safe, durable structures.
For structural applications, always involve qualified structural engineers and follow applicable building codes and design specifications. While ASTM A500 provides material requirements, structural design must consider all load conditions, connection details, and service environments.





