Overview of ASTM A335 P22 Seamless Steel Pipe
ASTM A335 is the standard specification for seamless ferritic alloy steel pipe intended for high-temperature service. Grade P22 is the 2.25Cr-1Mo grade of that specification: a chromium-molybdenum alloy steel pipe produced by hot working a solid billet into a seamless hollow with no longitudinal weld, then sized, finished and heat treated. ASME SA335 P22 is the code edition of the same specification and is technically equivalent for design and procurement purposes.
Grade P22 is selected where carbon steel has reached its temperature limit but the 9Cr grades would add unnecessary cost and welding complication. It is a mainstream material for superheater and reheater tubing, main steam piping, steam headers and hot process lines in refineries.
Chemical Composition and Its Effect on Performance
Chromium supplies the oxidation and scaling resistance that lets the pipe survive long exposure to hot combustion gas and steam. Molybdenum raises elevated-temperature strength and creep resistance, so the pipe resists slow deformation under sustained stress at temperature. The ASTM A335 P22 limits for heat analysis are:
| Element | Composition (%) |
|---|---|
| Carbon (C) | 0.05–0.15 |
| Manganese (Mn) | 0.30–0.60 |
| Phosphorus (P) | 0.025 max |
| Sulfur (S) | 0.025 max |
| Silicon (Si) | 0.50 max |
| Chromium (Cr) | 1.90–2.60 |
| Molybdenum (Mo) | 0.87–1.13 |
Phosphorus and sulfur are held low because both embrittle the steel and reduce toughness in the weld heat-affected zone. The restricted carbon range keeps hardenability predictable while still delivering the tensile strength the grade requires.
Mechanical Properties at Room Temperature
The specification fixes minimum values that must be met by tensile testing of samples taken from the finished pipe:
| Property | Requirement |
|---|---|
| Tensile strength | 415 MPa (60 ksi) min |
| Yield strength | 205 MPa (30 ksi) min |
| Elongation | 30% min in 2 in., as adjusted for wall thickness |
| Supply condition | Fully annealed, or normalized and tempered |
High-Temperature Service and Heat Treatment
P22 keeps useful creep strength up to approximately 593 °C (1100 °F) in steam and hot gas service, which is why it is used for the hottest sections of conventional boilers. The required heat treatment refines the grain structure, relieves forming stresses and delivers the strength and ductility combination the specification demands.
For welded construction, thermal control is the deciding factor in joint life. A 2.25Cr-1Mo steel hardens in the heat-affected zone and loses toughness if that zone is left untreated, so post-weld heat treatment is mandatory rather than optional.
Preheat before welding: typically 200–300 °C (400–575 °F).
Interpass temperature control to limit heat-affected zone hardness.
Post-weld heat treatment in a temperature range that tempers the heat-affected zone without reducing base metal strength.
Matching 2.25Cr-1Mo filler metals such as ER90S-B3 and E9015-B3 for gas tungsten arc and shielded metal arc welding.
Manufacturing, Testing and Inspection
Seamless pipe is produced by piercing a heated round billet to form a hollow shell, elongating and rolling that shell to the required diameter and wall thickness, then sizing and finishing the product. The absence of a weld seam produces a homogeneous cross-section with uniform properties around the full circumference, which is the reason this product family dominates high-pressure, high-temperature piping.
Quality is verified by a combination of destructive and non-destructive tests: hydrostatic pressure testing of every pipe, an electric non-destructive test such as eddy current or ultrasonic inspection for surface and internal defects, flattening, bend and hardness tests on samples, plus chemical analysis and tensile testing to confirm the grade.
Typical Applications and Grade Comparison
Fossil-fired power stations: superheater and reheater tubes, main steam lines and steam headers.
Petrochemical and refining: process piping around catalytic cracking and hydrocracking units.
Industrial and utility boilers: boiler tubing and connecting pipework.
Heat exchangers and pressure parts exposed to thermal cycling and high pressure.
| Grade | Nominal chemistry | Selection role |
|---|---|---|
| P11 | 1.25Cr-0.5Mo | Moderate temperature service at lower cost |
| P12 | 1Cr-0.5Mo | Lower chromium than P11, for lighter duty tubing |
| P22 | 2.25Cr-1Mo | Higher creep strength and oxidation resistance than P11 and P12 |
| P5 | 5Cr-0.5Mo | Better oxidation and sulfidation resistance than P22 |
| P9 | 9Cr-1Mo | Higher strength and scaling resistance for severe service |
| P91 | 9Cr-1Mo-V-Nb | Highest strength of the ferritic family, with thinner walls and stringent welding controls |
Frequently Asked Questions About ASTM A335 P22 Pipe
Q: What does the P22 designation mean in ASTM A335?
It identifies the 2.25% chromium, 1% molybdenum seamless ferritic alloy steel grade supplied for high-temperature service, commonly called 2.25Cr-1Mo steel.
Q: What is the maximum service temperature for P22 pipe?
Useful creep strength is generally accepted up to about 593 °C (1100 °F), with the exact limit set by the design code and the stress level in the component.
Q: Is ASME SA335 P22 the same material as ASTM A335 P22?
Yes. SA335 is the ASME code adoption of the same specification, and the grades are technically equivalent.
Q: What heat treatment is required for P22 pipe?
The pipe is supplied fully annealed or normalized and tempered, and welded joints require post-weld heat treatment before entering service.
Q: How does P22 differ from P11?
P22 contains 1.90–2.60% chromium and 0.87–1.13% molybdenum against roughly 1.25% chromium and 0.5% molybdenum in P11, giving P22 higher creep strength and better oxidation resistance.
Q: Can P22 pipe be welded in the field?
Yes, with qualified procedures: controlled preheat around 200–300 °C, matching 2.25Cr-1Mo filler metal, and post-weld heat treatment to restore heat-affected zone toughness.
A335 P22 remains a dependable choice for high-temperature, high-pressure piping because its chromium and molybdenum balance delivers proven performance at a cost and weldability level that more highly alloyed grades cannot match.





