May 22, 2025 Leave a message

ASTM A333 specification

Scope of ASTM A333

ASTM A333/A333M is the standard specification for seamless and welded steel pipe for low-temperature service. It covers nominal-wall pipe intended for service temperatures down to and below -150 deg F (-100 deg C), depending on the grade, and its central requirement is Charpy V-notch impact toughness measured at or below the design temperature. The specification is written in both inch-pound (A333) and SI (A333M) units, and it is used across oil and gas, LNG, cryogenic, and refrigeration installations where carbon steel pipe would fail in a brittle manner at low temperature.

The specification is organized into grades, each with its own chemical composition, heat treatment, and impact test temperature. The grade designation is chosen by the designer according to the minimum design temperature and the process conditions, and it must appear together with the standard number in every order, for example ASTM A333 Grade 6 or ASTM A333M Gr. 6.

Grade Overview

Grade Material Type Charpy Test Temperature Typical Use
1 Carbon steel -50 deg F (-45 deg C) General low-temperature piping
3 Nickel steel, nominally 3.5% Ni -150 deg F (-101 deg C) Low-temperature and cold-climate service
4 Nickel steel -150 deg F (-101 deg C) Cryogenic and low-temperature service
6 Carbon-manganese-silicon steel -50 deg F (-45 deg C) Most common grade for general low-temperature service
8 Nickel steel, nominally 9% Ni -320 deg F (-196 deg C) Cryogenic and LNG service
7, 9, 10, 11 Nickel-bearing and special compositions Per grade table Special cryogenic and low-temperature duty

Grade 6 is the workhorse of the specification: a plain carbon-manganese-silicon steel with good weldability, supplied in the normalized condition and impact-tested at -50 deg F (-45 deg C). Grade 3 adds nominally 3.5% nickel and is impact-tested at -150 deg F (-101 deg C), making it the preferred choice where the design temperature falls below the range of Grade 6. The higher-nickel grades such as Grade 8, with nominally 9% nickel, extend the specification to cryogenic temperatures around -320 deg F (-196 deg C), which is the boiling point of methane and the working range of LNG plants.

Key Requirements

Impact testing is the defining feature of A333. Test specimens are taken from the pipe body and are tested at a temperature no higher than the specified minimum service temperature. The standard requires that the results meet the absorbed-energy values in the specification table for the grade, with the full set of three specimens and the required average, and that the material remains ductile at the design temperature.

Manufacturing is covered for both seamless and welded pipe. Welded pipe must be produced by a qualified welding process, and the weld seam must meet the same low-temperature toughness requirements as the base metal. Heat treatment is specified per grade: Grade 6 is supplied normalized, and the nickel-bearing grades receive the heat treatment defined in the standard for their composition, typically normalizing or quenching and tempering, to develop the required toughness at low temperature.

A333 vs A106: Which One for Which Service

The two specifications are often confused because both cover carbon steel pipe in overlapping sizes. The selection rule is based on service temperature.

Criterion ASTM A333 ASTM A106
Design intent Low-temperature service, sub-zero conditions High-temperature service, steam and boiler systems
Mandatory impact testing Yes, Charpy V-notch at the design temperature Not required by the base specification
Typical grades 1, 3, 6, 8 and others for cryogenic duty A, B, C with higher carbon levels
Common failure concern Brittle fracture at low temperature Creep and oxidation at high temperature

A333 pipe is specified where the minimum design temperature is below about -29 deg C, which is the practical floor for A106 Grade B in many codes. A106 remains the standard choice for hot service. Where a system operates at both low and high temperature, the governing case decides, and some projects use A333 for the cold sections and A106 for the hot sections of the same line.

International Equivalents

System Equivalent Grade Reference
EN EN 10216-4 series for low-temperature tubes, with grade selection by composition and impact temperature
JIS JIS G3460 STPL380 for carbon steel low-temperature pipe
GB GB/T 18984 grades such as 16MnDG for low-temperature service

These equivalents are for cross-standard reference in substitution studies. A333 Grade 3, with its 3.5% nickel content, is frequently compared with the nickel-bearing low-temperature steels in EN 10216-4, while Grade 6 is compared with the plain carbon grades such as STPL380. Substitution must be confirmed against the project specification, because impact test temperatures and acceptance values differ between standards.

Applications

A333 pipe is specified wherever the design temperature falls below the ductile-to-brittle transition of ordinary carbon steel: LNG liquefaction and regasification plants, cryogenic storage and transfer lines, refrigeration systems, cold-climate oil and gas gathering and transmission lines, and low-temperature heat exchangers. In all of these services the buyer verifies the impact test results on the mill certificate against the design temperature before the pipe is released for installation.

FAQ

1. What is ASTM A333 used for?

It is used for seamless and welded steel pipe in low-temperature service, down to cryogenic temperatures depending on grade, mainly in oil and gas, LNG, and refrigeration systems.

2. What is the difference between Grade 3 and Grade 6?

Grade 6 is a carbon-manganese-silicon steel tested at -50 deg F (-45 deg C). Grade 3 contains nominally 3.5% nickel and is tested at -150 deg F (-101 deg C), so it serves lower design temperatures.

3. Does A333 require impact testing?

Yes. Charpy V-notch impact testing at or below the design temperature is mandatory for all grades, which is the defining requirement of the specification.

4. Is A333 pipe seamless or welded?

Both. The specification covers seamless and welded pipe; the welded product must meet the same low-temperature toughness requirements as the base metal.

5. What is the difference between A333 and A106?

A333 is designed for sub-zero service with mandatory impact testing, while A106 is for elevated-temperature service such as steam and boiler piping without mandatory impact testing.

6. What is A333 Grade 6 equivalent to?

It is commonly compared with JIS G3460 STPL380 and with the plain carbon grades of the EN 10216-4 low-temperature series; final substitution depends on the project specification and required impact temperature.

Send Inquiry