Sep 19, 2025 Leave a message

ASTM A252 SSAW Steel Pipe: Spiral Welded Pipe for Piling Foundations

ASTM A252 Pipe and the SSAW Process

ASTM A252/A252M is the standard specification for welded and seamless steel pipe piles. Spiral submerged arc welded pipe, usually shortened to SSAW, is one of the main manufacturing routes used to produce pipe that conforms to this specification. The pipe is intended to be driven into the ground to provide foundation support for buildings, bridges, wharves and retaining structures, so its primary duty is structural rather than the transport of fluids.

Because the specification is written around piling behaviour, the acceptance criteria are mechanical and dimensional: lot tensile testing against the ordered grade, verification of outside diameter and wall thickness, and examination of the welded seam.

How SSAW Pipe Is Made

A continuous coil or strip is uncoiled, levelled and edge trimmed, then fed through a series of forming rolls that bend it into a helix. The abutting edges are welded from the inside and the outside with the submerged arc process, producing a continuous helical seam. After welding the pipe is cut to length, and the ends are faced square and, when required, beveled for splicing.

The helical seam runs around the circumference of the pipe rather than along its axis.

Wide diameter ranges are produced from relatively narrow strip, which suits large diameter piles.

Inside and outside welding gives a double-sided, fully fused seam.

Specification Summary for SSAW Piling Pipe

Item Detail
Standard ASTM A252/A252M
Grades available Grade 1, Grade 2 and Grade 3
Grade 2 minimum yield strength 240 MPa (35,000 psi)
Grade 2 minimum tensile strength 414 MPa (60,000 psi)
Grade 3 minimum yield strength 310 MPa (45,000 psi)
Nominal outside diameter 219 mm to 3,620 mm (8 in to 144 in)
Length About 6 m to 24 m, or as ordered
Ends Plain or beveled, square cut
Testing Lot tensile test, dimensional checks, visual weld examination, optional non-destructive examination

Where SSAW Piling Pipe Is Used

Deep foundations for buildings and industrial plant on weak ground.

Bridge piers, abutments and elevated road structures.

Wharf and jetty piles in marine environments, with protective coating.

Retaining walls, cofferdams and excavation support.

Pipe roof and micro-pile schemes for tunnelling and slope stabilisation.

Selection and Processing Guidance

Choose the grade first, then size the wall thickness against the driving stress and the design load. For long piles, check that the hammer energy will not buckle the section, and consider a heavier wall or a higher grade if the driving resistance is expected to be severe.

Specify the coating system early. Fusion bonded epoxy, three layer polyethylene and bituminous coatings are all used, and the choice depends on soil chemistry and the design life.

Prepare bevels to the agreed profile and keep them free of rust, oil and moisture before splicing.

Check the seam and the pipe ends on arrival for laminations and mechanical damage.

Store on timber supports clear of standing water and keep the bore capped.

FAQ

Q: Is SSAW pipe the same as spiral welded pipe?
Yes. SSAW stands for spiral submerged arc welded, and it describes the helical seam formed from strip and welded inside and outside by the submerged arc process.

Q: Does the spiral seam reduce the strength of the pile?
No. The pipe is tested against the mechanical requirements of the ordered grade, and the helical seam distributes driving stress around the circumference rather than concentrating it on a single longitudinal line.

Q: Can SSAW pipe be supplied in Grade 3?
Yes. Spiral welded pipe is regularly produced to A252/A252M Grade 3 where a minimum yield strength of 310 MPa is required.

Q: What is the usual diameter range for spiral welded piles?
Large diameters are the natural strength of the process, and A252/A252M itself covers nominal outside diameters from roughly 219 mm up to 3,620 mm.

Q: How is the pipe protected in marine service?
Normally by an external coating such as fusion bonded epoxy or a multi-layer polyolefin system, with additional protection in the splash zone and a corrosion allowance in the wall thickness.

Q: Is hydrostatic testing part of the order?
Not as a routine acceptance test. Pipe piles are structural members, so the acceptance evidence is the lot tensile test and the dimensional and seam inspection.

Send Inquiry