

ASTM A252 ERW Pipe
Basic Overview
ASTM A252 is the standard specification for welded and seamless steel pipe piles used in foundation construction [citation:1, citation:3]. This standard covers pipe piles that serve as permanent load-carrying members or as shells for cast-in-place concrete piles [citation:1, citation:8]. ERW (Electric Resistance Welded) is one of the permitted manufacturing methods for ASTM A252 pipes, alongside HSAW, LSAW, and seamless [citation:2, citation:3, citation:7].
Name Explanation
| Part | Meaning |
|---|---|
| ASTM | ASTM International (American Society for Testing and Materials) |
| A252 | Standard specification for welded and seamless steel pipe piles [citation:1, citation:8] |
| ERW | Electric Resistance Welded – pipe formed from steel coil and welded longitudinally without filler metal |
Key Features
| Feature | Description |
|---|---|
| Primary Application | Foundation piling for buildings, bridges, docks, and marine structures [citation:3, citation:7] |
| Manufacturing Methods | ERW, HSAW (spiral), LSAW, and seamless [citation:2, citation:3, citation:7] |
| Grades | Grade 1, Grade 2, Grade 3 [citation:2, citation:3, citation:8] |
| Size Range (ERW) | NPS 1 to NPS 24 (33.4 mm to 609.6 mm OD) |
| Wall Thickness | 3 mm to 12 mm typical for ERW; up to 50.8 mm for larger manufacturing methods |
| Length | Min 3 m, Max 18 m, or custom |
| Surface Treatment | Normally bare or black varnish; galvanized available [citation:4, citation:8] |
Chemical Composition
ASTM A252 does not specify mandatory chemical composition limits, only mechanical properties. The standard only sets maximum limits for phosphorus and sulfur [citation:2, citation:8]:
| Element | Requirement |
|---|---|
| Phosphorus (P) | 0.050% max [citation:2, citation:4] |
| Sulfur (S) | 0.060% max (typical) |
Note: Manufacturers may provide typical composition values such as C ≤ 0.25%, Mn ≤ 0.95%, etc., but these are not mandated by the standard .
Mechanical Properties
| Grade | Yield Strength (min) | Tensile Strength (min) | Elongation (min) |
|---|---|---|---|
| Grade 1 | 205 MPa (30,000 psi) [citation:2, citation:8] | 345 MPa (50,000 psi) [citation:2, citation:8] | Determined by wall thickness |
| Grade 2 | 240 MPa (35,000 psi) [citation:2, citation:8] | 415 MPa (60,000 psi) [citation:2, citation:8] | Determined by wall thickness |
| Grade 3 | 310 MPa (45,000 psi) [citation:2, citation:8] | 455 MPa (66,000 psi) [citation:2, citation:8] | Determined by wall thickness |
Dimensional Tolerances
| Parameter | Tolerance |
|---|---|
| Outside Diameter | ±1% of specified OD [citation:2, citation:8] |
| Wall Thickness | Minimum wall not more than 12.5% under nominal [citation:2, citation:8] |
| Weight | Not more than 15% over or 5% under theoretical weight [citation:2, citation:8] |
Testing Requirements
| Test Type | Requirement |
|---|---|
| Chemical Analysis | Heat analysis required; product analysis as specified |
| Tensile Test | Per lot; yield and tensile strength verified [citation:2, citation:8] |
| Flattening Test | Required for weld integrity verification |
| Hydrostatic Test | Not specified – piling pipes are not used for fluid conveyance; typically filled with concrete [citation:2, citation:8] |
Grade Comparison
| Grade | Yield Strength | Tensile Strength | Strength vs. Grade 1 | Typical Application |
|---|---|---|---|---|
| Grade 1 | 30,000 psi | 50,000 psi | Baseline | Light-load foundations, good soil conditions [citation:3, citation:8] |
| Grade 2 | 35,000 psi | 60,000 psi | +17% | Most common grade – general piling applications [citation:3, citation:8] |
| Grade 3 | 45,000 psi | 66,000 psi | +50% | Heavy-load applications, bridges, offshore platforms [citation:3, citation:8] |
Applications
| Application | Description |
|---|---|
| Bridge Piling | Primary foundation for bridge construction |
| Dock Construction | Withstands heavy loads and maritime environmental pressures |
| High-Rise Building Foundations | Ensures structural stability for long-term use |
| Underground Casing | Drilled shafts and substructure applications |
| Marine Structures | Wharves, ports, and offshore platforms |
Key Advantages
| Advantage | Description |
|---|---|
| High Durability | Withstands heavy loads and extreme environmental conditions |
| Multiple Grades | Allows selection based on project load and design requirements |
| Various Welding Options | Available in ERW, HSAW, LSAW, and seamless to suit different applications [citation:3, citation:7] |
| No Hydrostatic Test Required | Reduces manufacturing cost since piling pipes are not used for fluid conveyance [citation:2, citation:8] |
| Galvanizing Option | Hot-dip galvanized available for corrosion resistance [citation:4, citation:10] |
Important Considerations
1. ERW Size Limitations
ERW manufacturing is typically used for sizes up to NPS 24 (609.6 mm OD)
Larger diameters require HSAW (spiral) or LSAW manufacturing [citation:2, citation:7]
2. Grade Selection
Grade 1: Light structural foundations, good soil conditions, temporary structures
Grade 2: Most common grade for general piling applications
Grade 3: Heavy-load applications, large bridges, offshore platforms
3. No Hydrostatic Test
Piling pipes are filled with concrete and not used for fluid conveyance
Hydrostatic testing is not specified in ASTM A252 [citation:2, citation:8]
4. Heat Treatment
Heat treatment requirements depend on the manufacturing method and grade
ERW pipes may require weld seam heat treatment to ensure proper properties
5. Coating Options
Black (bare): Standard finish
Hot-dip galvanized: For corrosion protection in outdoor/marine environments [citation:4, citation:10]
Varnish: Temporary protection during storage and handling
Summary
ASTM A252 ERW pipe is a standard specification for welded steel pipe piles used in foundation construction. Available in three grades with yield strengths ranging from 30,000 psi (Grade 1) to 45,000 psi (Grade 3), these pipes serve as permanent load-carrying members or shells for cast-in-place concrete piles in:
Bridge foundations
Dock and marine structures
High-rise building foundations
Underground casing and substructures
ERW manufacturing is suitable for sizes up to NPS 24 (24 inches OD). Unlike pressure pipe standards, ASTM A252 does not require hydrostatic testing since piling pipes are filled with concrete rather than used for fluid conveyance [citation:2, citation:8].
When ordering, specify: quantity, standard (ASTM A252), grade (1, 2, or 3), manufacturing method (ERW), outside diameter, wall thickness, length, and end finish (plain or beveled) .





