Nov 03, 2025 Leave a message

AS1163 Carbon Steel Pipe

info-225-225info-225-225

What is AS1163?

AS/NZS 1163 is the joint Australian and New Zealand Standard titled "Cold-formed structural steel hollow sections." It specifies the requirements for the manufacture of circular, square, and rectangular hollow sections (CHS, SHS, RHS) made from cold-formed steel, primarily used for structural purposes.

These pipes and tubes are ubiquitous in construction, mining, agriculture, and manufacturing due to their excellent strength-to-weight ratio.


Key Characteristics & Manufacturing

Manufacturing Process: The pipes are "cold-formed," meaning steel strip or plate is formed into a hollow section at ambient (room) temperature. This process work-hardens the steel, increasing its strength, particularly at the corners.

Material: The standard covers pipes made from welded carbon steel.

Shapes:

CHS (Circular Hollow Sections): What is commonly referred to as "pipe."

SHS (Square Hollow Sections): Square cross-section.

RHS (Rectangular Hollow Sections): Rectangular cross-section.

Surface Finish: Typically supplied with a mill scale (a dark blue/black oxide layer) or can be galvanized (zinc-coated) for corrosion protection.


Grades of Steel

AS1163 pipes are available in several grades, which define their minimum yield strength. The grade is a critical factor in structural design.

C250: Minimum yield strength of 250 MPa. This is a general-purpose grade.

C350: Minimum yield strength of 350 MPa. This is the most common grade for structural applications, offering a good balance of strength and formability.

C450: Minimum yield strength of 450 MPa. Used where higher strength is required to reduce weight or section size.

C550: Minimum yield strength of 550 MPa. A high-strength grade for demanding applications.

Note on "C": The "C" stands for "Cold-formed," indicating the enhanced strength from the manufacturing process.


Standard Sizes and Dimensional Tolerances

AS1163 provides precise tables for outside diameters (for CHS) and widths (for SHS/RHS), as well as wall thicknesses.

CHS Sizes: Range from small diameters (e.g., 21.3mm OD) to very large diameters (over 600mm OD).

Wall Thickness: Designated by a "t" value (e.g., t=3.0, t=6.0, t=12.7). The standard specifies permissible tolerances on diameter, wall thickness, ovality, and straightness.


Mechanical Properties (Summary)

The key mechanical properties defined by the grade are:

Property Description Typical Values (e.g., C350)
Yield Strength (Min) The stress at which the material begins to deform plastically. This is the primary design property. 350 MPa
Tensile Strength (Min) The maximum stress the material can withstand while being stretched before failing. 430 MPa
Elongation A measure of ductility (how much it can stretch before breaking). ~22% (varies with grade)

Common Applications

AS1163 pipes are incredibly versatile. You will find them in:

Structural Framing: The primary use. As columns, beams, trusses, and rafters in commercial, industrial, and residential buildings.

Handrails and Balustrading: SHS and CHS are the standard materials for handrail systems.

Mining and Resources: For structural supports, walkways, conveyor frames, and machinery guards.

Agricultural Machinery: For frames on tractors, harvesters, and other equipment.

Furniture and Fit-outs: Used in modern furniture, shop fittings, and architectural features.

Vehicle Frames and Roll Cages: Especially C450 and C550 grades for high-strength requirements.

General Fabrication: For any framework requiring a strong, lightweight, and readily available material.


Comparison with Other Pipe Standards

It's important not to confuse AS1163 with other common pipe standards:

Standard Full Name Primary Use Key Difference
AS1163 Cold-formed Structural Steel Hollow Sections Structural Support (load-bearing) Defined by mechanical properties (yield strength).
AS1074 Steel Tubes and Tubulars for Ordinary Service Fluid Transport (water, gas, air) Defined by a "Type" (e.g., Type 5, 20) based on internal pressure rating.
AS/NZS 3679.1 Structural Steel - Hot-rolled Bars and Sections Structural Sections (like universal beams, columns) Hot-rolled process (not cold-formed). Different manufacturing, different properties.

Simple Rule of Thumb: Use AS1163 for frames and structures that carry load. Use AS1074 for pipes that carry liquids or gases.


Important Considerations for Specifiers and Users

Design Standards: Structural design using AS1163 hollow sections must be carried out in accordance with AS 4100 (Steel Structures).

Welding and Fabrication: These pipes are readily weldable. However, for higher grades (C450, C550), more care must be taken with welding procedures to avoid weakening the heat-affected zone (HAZ).

Certification: For critical applications, you should request a Mill Certificate or Certificate of Conformity from the supplier, which provides verified test results for the chemical and mechanical properties of the specific batch of pipe.

Where to Find the Standard

The full, definitive specification can be purchased from Standards Australia (www.standards.org.au).

In summary, AS1163 Carbon Steel Pipe is the go-to standard for high-quality, cold-formed structural hollow sections in Australia and New Zealand. Its defined grades and tolerances make it a reliable and essential material for engineers, architects, and fabricators.

Send Inquiry