Resistance welded pipe, usually described as ERW pipe, is produced by cold-forming steel strip into a cylindrical shell and passing a high-frequency current through the abutting edges. The resistance at the joint generates enough heat to bring the edges to forging temperature, and squeeze rolls consolidate the seam without any filler metal. The result is a longitudinal welded pipe with a narrow heat-affected zone, high dimensional repeatability and a production rate that makes it the most economical pressure and structural pipe for small and medium diameters.
Product Characteristics and Specifications
Resistance welded pipe is normally produced in outside diameters from about 1/2 inch to 24 inches, with wall thickness from thin gauge up to roughly 20 mm. Round, square, rectangular and elliptical sections can all be formed from the same coil feed, which makes the product attractive where the design needs a specific section shape rather than a circular bore.
| Parameter | Typical supply range | Governing standard |
|---|---|---|
| Line pipe | Grades up to X70, diameter to 24 in | API 5L |
| Pressure and general service | DN15 to DN600 | EN 10217, ASTM A53, GB/T 3091 |
| Structural hollow sections | Square and rectangular to 400 mm | ASTM A500, EN 10219, GB/T 6728 |
| Precision mechanical tube | Wall tolerance about ±0.1 mm | Automotive and machinery specifications |
| Surface finish | Bare, oiled, galvanised, painted, 3PE or FBE | Coating standards |
Mechanical properties follow the strip grade rather than the pipe making route, so a Q235B structural tube is expected to deliver the yield and tensile levels of GB/T 700 within the applicable thickness range, while an API 5L X65 line pipe is expected to meet the specified minimum yield strength and the toughness requirements of the applicable product specification level.
Application Fields
Oil and gas: gathering lines, low-pressure transmission lines, casing and structural supports. Continuous production suits long pipeline runs, and coated products resist soil and atmospheric corrosion. High-pressure mains still favour seamless or submerged-arc welded pipe.
Automotive: exhaust systems, chassis members, drive shafts, seat frames and cross car beams. The process delivers uniform wall, accurate diameter and shape flexibility, and volume production matches the automotive supply chain.
Construction: steel structure frames, scaffolding, guardrails, roof supports and cladding substructures. Galvanised tube gives the weather resistance needed for exposed building services and temporary works.
Home appliances: refrigerator frames, radiator shells, condenser supports and piping systems, where thin-wall tube reduces weight and cost and coated surfaces protect against condensation corrosion.
Mechanical equipment: hydraulic cylinder barrels, conveyor rollers, machine frames and guards. Precision welded tube can replace seamless tube in a number of these duties at lower cost.
Selection and Processing Guidance
Selection starts with the governing standard: API 5L where the pipe will carry hydrocarbons, EN 10217 or ASTM A53 for pressure and general service, ASTM A500, EN 10219 or GB/T 6728 for structural sections, and the relevant machinery specification where tight wall tolerance is required. Wall thickness is set by the design pressure or by section stiffness, and the weld seam should be placed away from the zone of maximum bending tensile strain during forming. Resistance welded pipe is readily cut, drilled, bent and welded on site; when the seam area is welded, the joint should be cleaned of scale and coating first, and a procedure suitable for the base grade should be used.
Inspection Points and Common Pitfalls
A normal quality plan includes flattening and reverse bend testing of the seam, full-section tensile testing, hydrostatic or eddy current testing, ultrasonic inspection of the weld, and dimensional verification of diameter, wall and ovality. Frequent mistakes include specifying a galvanised finish where the coating mass has not been confirmed, using scaffolding grade tube for pressure duty, and ordering a tolerance class the process cannot hold. Naming the standard, the grade and the tolerance on the purchase order prevents all three.
FAQ
Q: What is a resistance welded pipe?
It is a pipe formed from steel strip and joined longitudinally by the heat generated when high-frequency current passes through the strip edges, with the edges forged together under pressure and no filler metal added.
Q: How does resistance welded pipe compare with seamless pipe?
Welded pipe is generally lower in cost, more accurate in wall and diameter, and available in a wider range of section shapes, while seamless pipe retains an advantage for high-pressure, high-temperature and demanding fatigue service.
Q: Which industries use resistance welded pipes most?
Oil and gas gathering, automotive and transport equipment, construction and scaffolding, home appliances and general mechanical equipment are the main consuming sectors.
Q: Can resistance welded pipe be used in high-pressure service?
It is qualified for many medium-pressure duties and API 5L grades up to X70 are produced, but very high-pressure transmission mains are normally specified as seamless or longitudinal submerged-arc welded pipe.
Q: What tests verify the weld quality?
Flattening and reverse bend tests confirm ductility of the seam, ultrasonic inspection detects internal discontinuities, and hydrostatic or eddy current testing verifies integrity of the full length.
Q: Are square and rectangular welded pipes available?
Yes. Square, rectangular and elliptical hollow sections are produced from the same strip feed and are widely used for structural and architectural work as well as for machine frames.





