Why Peroxide Service Is Different
Hydrogen peroxide becomes progressively more reactive as its concentration rises. Above roughly seventy percent concentration it behaves as a strong oxidiser, and a contaminated surface can initiate violent decomposition that raises temperature and pressure inside the pipe. The design consequence is that the wetted system must be clean, passivated and free of catalytic metals, and that every material in contact with the medium has to be assessed for compatibility rather than chosen from a general corrosion table.
Material Selection
Austenitic stainless steel is the workhorse material for peroxide piping. The low-carbon grades of ASTM A312, particularly the molybdenum-bearing 316L type, are widely used because they combine corrosion resistance with good weldability and can be passivated to a stable oxide surface. Lower-carbon 304L tube is used in lower-concentration service where the operating window has been confirmed. Aluminium grades are applied in some storage and transfer systems because aluminium surfaces decompose peroxide slowly, but the choice depends on the concentration and must be supported by compatibility testing.
Specify low-carbon austenitic tube to ASTM A312 with the heat analysis and the surface finish recorded on the certificate.
Avoid copper, brass, bronze and their alloys in the wetted path, together with galvanised surfaces and any unpassivated metal.
Demonstrate material compatibility for the intended concentration by a standardised decomposition test before the line is released for service.
Keep the wetted area free of carbon steel fittings, temporary supports and tools during fabrication.
Cleaning and Passivation
Cleaning is a sequence rather than a single operation. Alkaline cleaning removes oils and organic residues, acid pickling removes scale and free iron from the surface, and high-purity water rinses carry the residues away. Passivation then rebuilds the chromium oxide layer, and its effectiveness is verified by the test methods described in ASTM A967. The finished surface is confirmed by wipe tests and particulate counts before the line is handed over.
Use dedicated, clean equipment for peroxide lines; carbon steel brushes, grinding debris and workshop dust are all contamination sources.
Rinse until the conductivity of the effluent stabilises, then dry with oil-free, filtered gas.
Cap or blank all openings immediately after cleaning so that the clean surface is not re-contaminated.
Joints, Welding and Layout
Permanent connections in peroxide service are normally made by orbital welding, which gives a repeatable full-penetration weld with a smooth internal bead and no crevice at the root. Flanged joints are used where the line must be opened, with gasket materials selected for peroxide compatibility, the fluoropolymer types being the usual choice. Layout matters as much as the weld: dead legs where liquid can stagnate and decompose are eliminated, low points are drained, and the number of threaded and socket-welded joints is kept to an absolute minimum.
Pressure Testing and Commissioning
Testing follows a graduated approach. The mechanical integrity of the line is proved first with an inert gas such as nitrogen rather than with liquid peroxide, and the system is then brought into service by progressive introduction of peroxide at increasing concentration while temperature, pressure and venting are monitored. Vent paths are sized for the gas evolution that decomposition would produce, and the vent gas is routed away from the working area. Instruments in contact with the medium follow the same material rules as the pipe.
FAQ
Q: Why is hydrogen peroxide piping treated as a special case?
Because the medium can decompose violently when it meets contamination. A clean, passivated, catalytic-metal-free system removes the surfaces that would otherwise initiate decomposition.
Q: Which pipe material is used for high-concentration peroxide?
Low-carbon austenitic stainless steel, usually the molybdenum-bearing 316L type to ASTM A312, with aluminium in use for some storage and transfer systems when the choice is supported by compatibility testing.
Q: How is peroxide pipe cleaned and passivated?
Alkaline cleaning removes organic residues, acid pickling removes scale and free iron, high-purity water rinses carry them away, and passivation rebuilds the oxide layer in accordance with ASTM A967, with the result confirmed by wipe tests and particle counts.
Q: What joint design is used?
Orbital welding for permanent joints, with a smooth internal bead and full penetration, and fluoropolymer gaskets on flanged connections that must be opened for maintenance.
Q: How is the system pressure-tested safely?
Mechanical integrity is proved first with an inert gas such as nitrogen, and peroxide is then introduced progressively at increasing concentration while temperature, pressure and venting are monitored.





