The Short Answer
Generally no, seamless pipe manufactured to GB/T 8162 should not be used for pressure piping. GB/T 8162 covers seamless steel tubes for structural and mechanical purposes, and it is not a pressure pipe standard. Pipes made to this standard are not required to undergo the mandatory hydrostatic testing and non-destructive examination that pressure service requires, so their pressure integrity is not verified. For pressure piping, the correct standard is GB/T 8163 or a dedicated pressure specification matched to the fluid and temperature.
What GB/T 8162 Actually Covers
GB/T 8162 specifies seamless steel tubes for structural and mechanical applications. The standard covers a wide range of carbon and alloy steels, including 10, 20, 35, 45, and alloy grades such as 40Cr and 35CrMo, and it defines the dimensions, tolerances, and mechanical properties of the tubes. The tests normally performed include tensile testing and dimensional inspection, but pressure-related verification is not part of the standard.
| Aspect | GB/T 8162 Structural Tube | GB/T 8163 Fluid Tube |
|---|---|---|
| Primary use | Structural and mechanical parts | Fluid and pressure service |
| Hydrostatic test | Not mandatory | Mandatory |
| Non-destructive examination | Not mandatory | Required |
| Flattening and flaring tests | Optional | Required |
| Impact testing | Optional | Specified for low temperature service |
Why the Distinction Matters
The difference between the two standards is not cosmetic. A tube intended for pressure service must withstand internal pressure without leaking or failing, which depends on sound material throughout the wall and the absence of critical defects. Structural tube is produced and tested for load-bearing and machining applications, where a small internal defect may be acceptable. Under pressure, the same defect could grow and cause a leak or rupture, so using structural tube for pressure is a safety risk as well as a code violation.
What to Specify for Pressure Piping
For water, air, steam, and general fluid service, GB/T 8163 is the appropriate Chinese standard. For high-temperature boiler and power plant service, GB 5310 grades such as 20G or 15CrMoG are used. For oil and gas transmission, API 5L or a project-specific standard applies. International projects may reference ASTM A106, A53, or EN 10216 depending on the design code. In every case, the standard must include pressure testing and non-destructive examination requirements.
Special Cases and Exceptions
In some projects, GB/T 8162 tubes are accepted for low-risk services such as instrument air or vent lines where the design pressure is negligible and the design code permits it. This is an engineering decision made by the responsible designer, not a general rule. When in doubt, the tube should be specified to a pressure standard, and the design code should be consulted before any substitution is considered.
How to Order the Right Tube
When ordering seamless tube, state the standard together with the grade, outside diameter, wall thickness, length, and delivery condition. For pressure service, add the required test certificate and any supplementary requirements such as ultrasonic testing. A complete specification prevents the delivery of structural tube to a pressure application and gives the quality assurance team the documentation they need.
FAQ
What is the difference between GB/T 8162 and GB/T 8163?
GB/T 8162 covers seamless tubes for structural and mechanical purposes, while GB/T 8163 covers seamless tubes for fluid and pressure service. The pressure standard adds mandatory hydrostatic testing, non-destructive examination, and flattening tests that the structural standard does not require.
Can structural tube be hydrostatically tested and used?
Testing a structural tube to prove pressure integrity is possible in principle, but the tube was not produced with the same quality controls as pressure tube, and the test does not restore the missing inspection requirements. The safe and code-compliant approach is to specify a pressure standard.
Why are alloy grades like 35CrMo in GB/T 8162 used?
Alloy grades in GB/T 8162 are specified for high-strength mechanical components such as hydraulic cylinders, shafts, and mining support columns, not for pressure piping. They are selected for load capacity and hardenability, not for pressure integrity.
Which standard should be used for water supply lines?
For water supply and general fluid service, GB/T 8163 is the appropriate standard. For higher-pressure or higher-temperature service, the design code will direct the selection of a suitable pressure standard.
Is the risk really significant?
Yes. Internal defects that are harmless in a structural member can grow under cyclic pressure and cause a leak or rupture. The mandatory testing in pressure standards exists precisely to catch these defects before the pipe enters service.
What should be written on the purchase order?
The purchase order should state the standard, grade, size, wall thickness, length, delivery condition, test certificate type, and any supplementary inspection requirements. This ensures the tube is produced and tested for the intended service.





