ERW API 5L X56 Carbon Steel Pipes
video

ERW API 5L X56 Carbon Steel Pipes

ERW API 5L X56 carbon steel pipes are high-frequency welded line pipes at the X56/L390 strength level, produced from controlled carbon steel strip. Also bought as x56 erw carbon pipe or api 5l x56 electric resistance welded pipe, they carry oil, gas and water at medium diameters. X56 sets a 390 MPa minimum yield, while the ERW seam gives close OD and wall control and a fully inspectable weld.
Send Inquiry
Chat Now
Product Introduction

ERW API 5L X56 Carbon Steel Pipes

ERW API 5L X56 carbon steel pipes are high-frequency welded line pipes at the X56/L390 strength level, produced from controlled carbon steel strip. Also bought as x56 erw carbon pipe or api 5l x56 electric resistance welded pipe, they carry oil, gas and water at medium diameters. X56 sets a 390 MPa minimum yield, while the ERW seam gives close OD and wall control and a fully inspectable weld.

StandardAPI 5L / ISO 3183
GradeX56 / L390
ProcessHFW / ERW
LevelsPSL1 / PSL2
Yield, min390 MPa (56 ksi)
Tensile, min490 MPa (71 ksi)
OD range~60–660 mm
DocumentsEN 10204 3.1 / 3.2 + NDT
A carbon X56 ERW enquiry needs the grade, PSL and impact temperature together - omitting the last two changes both the mill route and the test bill. Send the diameter, wall, PSL and service and we will quote a fully tested pipe with MTC. Request a quotation.

Product Overview: X56 ERW Carbon Steel Pipes

ERW API 5L X56 carbon steel pipes are high-frequency welded line pipes at the X56/L390 level, made from micro-alloyed carbon strip. They combine a 390 MPa minimum yield with the tight dimensional accuracy of the ERW process and are used for oil, gas and water transmission at medium diameters.

Grade and Standard Designation

X56 is the API 5L grade with a minimum yield of 56,000 psi (390 MPa), designated L390 in ISO 3183. ERW describes the longitudinal high-frequency seam, and carbon steel identifies the base material rather than a coating or alloy grade.

Specification Levels and Delivery

PSL1 covers base chemistry, minimum strength and hydrostatic testing. PSL2 tightens chemistry, sets upper strength limits, caps yield-to-tensile at 0.93, requires Charpy impact testing and full-length seam NDE.

Chemical Composition

The limits shown are indicative maximum mass percentages for X56 (L390) carbon ERW strip. Carbon and sulfur are kept low so the high-frequency seam and the field girth weld remain tough and crack-free.

Chemical limits for X56 (L390), wt% - indicative API 5L values
Element PSL1 max PSL2 max Role
Carbon (C) 0.26 0.24 Base hardenability; capped for field weldability
Manganese (Mn) 1.40 1.40 Principal solid-solution strengthening element
Phosphorus (P) 0.030 0.025 Restricted more tightly at PSL2
Sulfur (S) 0.030 0.015 Inclusion control; tighter at PSL2
Silicon (Si) Not specified 0.45 Deoxidising addition
Nb + V + Ti ≤ 0.15 ≤ 0.15 Micro-alloy grain refinement
Carbon equivalent (CE) Not required ≤ 0.43 Limits heat-affected-zone hardening

Mechanical Properties

Strength data are the API 5L baseline for X56 carbon ERW product. At PSL2 the delivered pipe must fall inside a controlled band and meet the specified Charpy impact value.

Mechanical property band for X56 (L390) - indicative API 5L values
Property PSL1 PSL2
Yield strength (Rt0.5) min 390 MPa 390–545 MPa
Tensile strength (Rm) min 490 MPa 490–760 MPa
Yield / tensile ratio Not specified ≤ 0.93
Elongation Per API 5L formula Per API 5L formula
Charpy V-notch Not required Required at project temperature

Dimensions and Weight

X56 ERW carbon pipe is offered from about NPS 2 to NPS 26 with walls near 3–22 mm; the table shows representative ERW dimensions. Plain-end theoretical mass uses 0.0246615 × (OD − WT) × WT kg/m and is indicative only; ordered tolerances change actual mass.

Indicative X56 size options and theoretical mass
Outside diameter (mm) Wall thickness (mm) Mass (kg/m) Route / note
60.3 3.91 5.44 ERW
114.3 6.02 16.08 ERW
168.3 7.11 28.26 ERW
219.1 8.18 42.55 ERW
273.0 9.27 60.29 ERW
355.6 10.0 85.23 ERW

Dimensional Tolerances

Tolerance limits follow API 5L and the purchase specification. The figures below are common indicative values; the applicable standard edition and the project data sheet govern acceptance.

Indicative dimensional tolerance limits
Parameter Indicative tolerance
Outside diameter ±0.5% or ±1.6 mm, whichever is greater (body)
Wall thickness ±8% to ±12.5% of nominal, by size and process
Length ±50 mm on random and fixed cut lengths
Straightness Typically ≤ 0.2% of total length
Ovality Within the API 5L limit for the ordered OD and wall
End bevel Per ASME B16.25 where bevelled ends are ordered

Mill Route and Carbon Chemistry

X56 ERW starts from coil whose chemistry is designed for both strength and weldability.

Strip and Seam

Micro-alloying raises yield to 390 MPa without excessive carbon. The cleaned strip is roll-formed and the edges are heated by high-frequency current and forged together, so the seam inherits the body chemistry and stays narrow.

Finishing and Test

The seam may be normalised to refine grain, then the pipe is sized, straightened and cut. Each length is hydrostatically tested and the weld is examined along its full length before coating or despatch.

Ordering and Documentation

State grade X56 (L390), the PSL level and the delivery state on the order.

Give the impact test temperature when PSL2 is required.

Specify seam NDE method and the end finish for field welding.

Require EN 10204 3.1 or 3.2 MTC with heat traceability.

Related Products

For specification comparison, these related line-pipe pages may be useful:

API 5L X56 resistance welded pipe

API 5L X56 PSL2 pipe

ERW X46/X52 line pipe

API 5L X56 spiral welded pipe

Frequently Asked Questions

What are ERW API 5L X56 carbon steel pipes?

They are carbon-steel line pipes at the X56/L390 grade whose longitudinal seam is made by high-frequency electric resistance welding, used for oil, gas and water transmission at medium diameters.

What is the L390 designation for X56 carbon pipe?

L390 is the ISO 3183 metric designation matching API 5L grade X56. Both call for a minimum yield strength of 390 MPa (56,000 psi).

Which PSL level is common for X56 ERW carbon pipes?

PSL1 is common for general transmission; PSL2 is chosen when a strength band, lower phosphorus and sulfur, carbon-equivalent control, Charpy impact and seam NDE are required.

What is the tensile strength of X56 carbon steel pipe?

Under API 5L, X56 has a minimum tensile strength of 490 MPa (71,000 psi), with a minimum yield of 390 MPa; PSL2 also applies upper strength limits.

What sizes are ERW X56 carbon steel pipes supplied in?

ERW X56 is typically made from about NPS 2 to NPS 26 (60–660 mm) with walls near 3–22 mm; larger diameters move to LSAW or SSAW.

How is an X56 carbon ERW pipe ordered for a project?

The order states grade X56/L390, the PSL level, delivery state, diameter, wall, length, impact test temperature if PSL2, seam NDE scope and end finish.

Does X56 ERW carbon pipe need post-weld heat treatment?

Not always. The seam may be normalised to refine grain and restore toughness depending on the delivery state and project specification; PSL2 orders commonly define this treatment.

What mill documents come with X56 ERW carbon pipes?

A mill test certificate to EN 10204 3.1, or 3.2 when ordered, with heat chemistry, tensile and impact results, hydrostatic and NDE records, dimensional checks and a certificate of conformity.

Values shown are indicative and cross-checked against API 5L / ISO 3183 and independent mill references; final dimensions, chemistry, heat-treatment condition and test scope are governed by the purchased edition of the standard and the project data sheet.

a53 pipe
API 5L Grade B Pipe
API 5L X42 X46 X52 Welded Pipe

Hot Tags: erw api 5l x56 carbon steel pipes, China erw api 5l x56 carbon steel pipes manufacturers, suppliers, Electrofusion Welding HDPE Pipe For Irrigation, Welded HDPE PE100 Water Supply Pipes, Water Supply Pipes, A519 Pipe, Polyethylene Pipe For Water Supply, PE100 Water Supply Pipe

Send Inquiry